حل مشكله The system has been destroyed لهاتف Redmi 8A Pro olivewood

**ProfKefah** · 17-02-2022, 02:52 PM

السلام عليكم
شكرا لكل من ساعدني

الهاتف جاء بالمشكلة المذكورة بعد التحديث الهوائي حسب كلام الزبون

نحتاج التيست بوينت لادخال الهاتف وضع EDL لقراءة معلوماته وتفليشه

دد

Found Port
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00007200
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD37993 0D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_035]...Done
Executing Loader...OK
Auth Enabled Device! You may need Mi Auth Account to service!
Skipping Auth...OK
Detecting Stroage Type...OK
Hardware : 8937, EMMC, 32 GB
LU Count : 3 [0x03A3E000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi
Software : , V12.5.6.0.QCQINXM [Tue Dec 28 15:35:41 CST 2021]
Android Ver. : 10
Patch Level : 2021-12-01
USERDATA : Normal
You can use RESET LOCKS to remove Pin/Pattern/Password WITHOUT Data Loss.
Operation Finished.
QcFire Ver. 7.5

ننزل اخر اصدار من هنا

Xiaomi Redmi 8A Pro/Dual Firmware ROM TWRP (olivewood)

نفلش الجهاز

Operation : FlashChecking for existing devices...Not Found
Turn Off phone, hold Vol UP + Vol DOWN and insert USB cable.
Some phones may need Special Boot Cable or TestPoint for EDL mode.
Found Port : Qualcomm HS-USB QDLoader 9008 (COM7)
Driver Info : Qualcomm Incorporated, qcusbser.sys, 2.1.1.2
Connecting to phone...OK
Waiting for response...OK
Init Handshake Sequence...OK
Hardware ID : E1F00B00 [8937] 00007200
OPK_DATA : 079E496E26A477B120DFCD85DF7E4AD067164D8292DDD379930D5891E3D8240B
Initializing Protocol...OK
Using Auto Loader Selection [1]
Preparing Loader...Done
Sending Loader [8937_035]...Done
Executing Loader...OK
Auth Enabled Device! You may need Mi Auth Account to service!
Skipping Auth...OK
Detecting Stroage Type...OK
Hardware : 8937, EMMC, 32 GB
LU Count : 3 [0x03A3E000] [0x00002000] [0x00002000]
WARNING! High Speed Driver is not installed.
Please install driver from QcFire\Drivers folder using Device Manager.
Payload Info : In: 262144 [4096], Out: 1048576, Sector Size: 512
Reading Partition Table...OK
Reading Device Information...OK
Device : Xiaomi
Software : , V12.5.6.0.QCQINXM [Tue Dec 28 15:35:41 CST 2021]
Android Ver. : 10
Patch Level : 2021-12-01
Writing [sec.dat] -> [sec] ...Done
Writing [vbmeta.img] -> [vbmeta] ...Done
Writing [vbmeta.img] -> [vbmetabak] ...Done
Writing [devcfg.mbn] -> [devcfg] ...Done
Writing [devcfg.mbn] -> [devcfgbak] ...Done
Writing [dummy.img] -> [apdp] ...Done
Writing [dummy.img] -> [msadp] ...Done
Writing [sbl1.mbn] -> [sbl1] ...Done
Writing [sbl1.mbn] -> [sbl1bak] ...Done
Writing [rpm.mbn] -> [rpm] ...Done
Writing [rpm.mbn] -> [rpmbak] ...Done
Writing [cmnlib_30.mbn] -> [cmnlib] ...Done
Writing [cmnlib_30.mbn] -> [cmnlibbak] ...Done
Writing [cmnlib64_30.mbn] -> [cmnlib64] ...Done
Writing [cmnlib64_30.mbn] -> [cmnlib64bak] ...Done
Writing [km4.mbn] -> [keymaster] ...Done
Writing [km4.mbn] -> [keymasterbak] ...Done
Writing [misc.img] -> [misc] ...Done
Writing [emmc_appsboot.mbn] -> [aboot] ...Done
Writing [emmc_appsboot.mbn] -> [abootbak] ...Done
Writing [tz.mbn] -> [tz] ...Done
Writing [tz.mbn] -> [tzbak] ...Done
Writing [dtbo.img] -> [dtbo] ...Done
Writing [dtbo.img] -> [dtbobak] ...Done
Writing [splash.img] -> [splash] ...Done
Writing [adspso.bin] -> [dsp] ...Done
Writing [adspso.bin] -> [dspbak] ...Done
Writing [persist.img] -> [persist] ...Done
Writing [mdtp.img] -> [mdtp] ...Done
Writing [mdtp.img] -> [mdtpbak] ...Done
Writing [boot.img] -> [boot] ...Done
Writing [recovery.img] -> [recovery] ...Done
Writing [cache.img ] -> [cache]...Done
Writing [NON-HLOS.bin] -> [modem] ...Done
Writing [system.img ] -> [system]...Done
Writing [vendor.img ] -> [vendor]...Done
Writing [cust.img ] -> [cust]...Done
Writing [userdata.img ] -> [userdata]...Done
Writing [gpt_main0.bin] -> [PrimaryGPT] ...Done
Writing [gpt_backup0.bin] -> [BackupGPT] ...Done
Applying Patches................Done
Reading Partition Table...OK
Resetting FRP Lock......Done
Resetting device...Done
Operation Finished.
QcFire Ver. 7.5