السلام عليكم
Factory/bootrom mode (HUAWEI USB COM 1.0) service functions are now available on Huawei phones with HarmonyOS!
الوظائف المدعومه بالوضع المصنعي البوت روم بتعريف huwaei usb com 1.0 لنظام هارموني
Here are some of our most used factory/bootrom mode functions:
الوظائف الموجودة
FRP and Huawei ID Remove
ازالة قفل frp وحساب هواوي
Modify OEMInfo (Vendor/Country, Disable FW version check, ...)
تعديل معلومات oem info الوجهة والدولة وتعطيل تفحص اصدار النظام في الهاتف
Load Factory Fastboot (partially supported; updates in progress)
And many more...
مع الدعم الجزئي لوضع الفاست بوت المصنعي علما ان التحديثات مستمرة
Supported CPUs: Kirin 710/710A/710F, 810/820, 980/985, 990/990 5G
دعم معالجات كيرين اعلاها
The Problem
المشكلة
Due to some changes done by Huawei, phones that are updated to HarmonyOS, would not present the Huawei USB COM 1.0 serial port after test pointing. Without the Huawei USB COM 1.0 serial port Chimera cannot communicate to these devices in factory/bootrom mode.
بعد التغييرات التي اجرتها شركه هواوي على الهواتف المحدثه لنظام هارموني لتجعلها لا تظهر بتعريف Huawei USB COM 1.0 بعد عمل التيست بوينت والذي معناه عدم امكانية الدخول لوضع factory/bootrom
The Solution
الحل
You need to use a modified USB cable, we call it the "Harmony TP Cable". If this cable is used, Huawei USB COM 1.0 serial port is available and all Chimera factory/bootrom mode service functions will work on HarmonyOS models.
ستحتاج لكيبل معدل ندعوه كيبل التيست بوينت لنظام هارموني
عند استعماله سيظهر التهاتف بالتعريف هواوي يو اس بي كوم واحد فارزة صفروعندها كل العمليات بالوضع البوت روم المصنعي ستعمل
Harmony TP Cable, How-to
كيفية عمل الكيبل
What you need:
1 pc. 150 Ohm (150 Ω) resistor
1 pc. 270 Ohm (270 Ω) resistor
1 pc. 1.5 kiloohm (1.5 kΩ) resistor
المقاومات اعلاها
and 1 pc. standard USB cable
كيبل يو اس بي اصلي
Here is how-to make the cable:
كيفيه العمل
Important Notes
التنويهات
You still have to test point (this cable only works if the test pointing is done)
سيعمل الكيبل فقط اذا وصلت نقاط التيست بوينت
Make sure that you always connect the cable to the phone first
وصل الكيبل اولا الى الهاتف
Make sure, when asked to disconnect you always disconnect the cable from the computer first
عند سؤالك عن فصل الكيبل افصل جهة الحاسوب اولا
You have to see the Huawei USB COM 1.0 serial port in Windows Device Manager. If you cannot see it, most probably the modified cable is wrong.
سيظهر الهاتف بالوضع هواوي يو اس بي واحد في ادارة الاجهزة
وان لم يظهر هنالك خطا في الكيبل
FAQ
معلومات
Why do I see unknown device in Windows Device Manager?
لماذا يظهر الجهاز كغير معروف في ادارة الاجهزة
Most probably you connected the cable to your computer first. Please make sure that you connect the cable to the phone first.
عالاغلب انك وصلت طرف الحاسوب اولا .تاكد من انك وصلت طرف الهاتف اولا
I disconnected the cable but I can still see the phone connected, why?
فصلت الكيبل ولكني لا ارى الهاتف موصل
Most probably you disconnected the cable from the phone first, and not the computer. Please make sure that you always disconnect the cable from the computer first.
هذا لانك فصلت جهة الهاتف .تاكد من انك تفصل داما من جهة الحاسوب اولا دائما
فديو للتوضيح اكثر
تحديث مخيف من كايميراشيمراتول بعداغلاق هواوي لثغرةالتيست بوينت Harmony TP Cable huwae
المفضلات