condor l4pro dead boot fixed by cm2sprd2
Infinity-Box Chinese Miracle II : SPD/USC Module [SP2] v2.13
Load IDBase v8331 Ok!
Open : SPD_PROG.xml
Reading package ...
Read package finished!
Created by Infinity-Box (c) 2020
Chinese Miracle II : Spreadtrum / UniSoc Service Module
Device Info file : _Android_info.txt
Patch Level : PPR1.180610.011
Display ID : SP653_V10_20190911
Ver. Incmt : 108
Ver. CodeName : REL
Ver. Release : 9
Sec. Patch : 2019-09-05
Build Time : 1568136356
Product Model : Plume L4 Pro
Product Brand : Condor
Product Name : Plume_L4_Pro
Product Device : Plume_L4_Pro
Product Manfct : SPA Condor Electronics
Product Info : Plume_L4_Pro
Product Board : sp9863a_1h10
Board Platform : sp9863a
SECSolution : MODERN [RS/0S/1S/2S]
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : INF : INFINITY FW PACKAGE
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
>>> ERROR : FLASH FDL NOT started!
>>> Error : Fail to boot FDL!
>>> Unsupported device with selected fdl or settings! Change settings!
Reconnect Power/Cable!
Operation : Flash Firmware [ v2.13 ]
Setting : Update NVRAM : False
Setting : Force NVRAM : False
Setting : Update PMT : True
1. Power off device, wait 10-15 seconds
2. Press and hold BooKey ( 1 : BOTH VOL , 2 : VOL+ , 3 : VOL- )
3. Insert cable in device!
Wait for device ...
Device Connected!
BootVersion : SPRD3
Boot : INF : INFINITY FW PACKAGE
Sending Init Boot ...
Boot sent!
Kick FDL ...
BootVersion : Spreadtrum Boot Block version 1.1
Protocol setup ...
Port speed : 921600
Sending Flash Boot ...
Boot sent!
Kick FLASH FDL ...
FDL : 0x0004
FDL : EMMC_RO : False ; EMMC_PART : True ; EMMC_RPMB_SET : True
FDL : Control transfered!
Boot Done!
PMTMng : Load PMT
PMTMng : 0x24
PMTMng : Update PMT Ok!
Prepare target ...
Prepare Ok!
UBOOT : u-boot.bin
UBOOT : u-boot.bin
CODE : sml.bin
CODE : sml.bin
CODE : tos.bin
CODE : tos.bin
CODE : vbmeta.img
CODE : vbmeta.img
CODE : dtb.img
CODE : dtbo.img
CODE : ldsp_l.bin
CODE : gdsp_l.bin
CODE : modem_l.bin
CODE : modem_wcn.img
CODE : gnssmodem.bin
CODE : gnssbdmodem.bin
CODE : pm_sys.bin
CODE : boot.img
CODE : recovery.img
FSIMG : persist.img
CODE : boot_logo.bmp
CODE : fastboot_logo.bmp
FSIMG : system.img
FSIMG : vendor.img
FSIMG : otp_product.img
FSIMG : userdata.img
FSIMG : cache.img
FSIMG : prodnv.img
CODE : deltanv_l.bin
UBOOT : u-boot-spl.bin
ERASE : FLASH_L
ERASE : MISC
ERASE : UBOOT_LOG
Flashing finished!
Reconnect Power/Cable!
Done!
Elapsed: 00:06:04
.gif)
المفضلات