لو سمحتوا يا جماعه برجائء المساعده ضروري

[ana_nasr2000]

جهاز تكنو c7 واقف علي الافتتاحيه الفلاشه المسحوبه منه MT6735_EMMC_MRA58K__6_0_TECNO-C7_TECNO_2020_07_20_21_25) فلشته فلش تمام ونفس المشكله هل في حل وشكرا

[allttar]

حاول تعمل فورمات بدخول للريكروفي
آلم ينجح ضع آنفو بقرآة الجهاز

[ana_nasr2000]

عملت فورمات من الريكفري نفس المشكله

[ana_nasr2000]

Wait for phone...
Phone found! [ 13 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6735
BB_CPU_NME : [MediaTek] MT6735_S00
BB_CPU_EXT : 0xCA00 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x93
NAND Flash : NOT INSTALLED
eMMC Flash : 484A01906532474164350705EF9862DE
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x90 , OEM : 014A
[eMMC] : FLASH_INF : [HYNIX] , e2GA
[eMMC] : FLASH_CID : 90014A484147326505073564DE6263EF
[eMMC] : FLASH_BRT : 0x00400000 , 0x00400000 , 0x00400000
[eMMC] : FLASH_LEN : 0x00000003AB800000
[eMMC] : FLASH_UCP : 15032 MiB [eMMC 16 GiB]
DEV RID : 0x666DA76FA3BBE4923CC3BC35A09A1F7E
INT RAM : 0x00020000
EXT RAM : 0x80000000 [2 GiB]
BOOT TYPE : EMMC_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!

[AP] : Initial info read Ok!


SECURITY :
IMEI_SW [1] : 359396071508427
IMEI_SW [2] : 359396071508435
BTMAC Addr : 78FFCA4BD538
WiFi MAC : 78FFCA4BA1A8

Done!
Elapsed: 00:00:13
Reconnect Power/Cable!


انفو من cm2

[ana_nasr2000]

Action : Boot Info.
Selected 0-By CPU:ELBRUS
Exe version: NCKDongle AndroidMTK 2.6.5
Reinsert phone battery.
Battery must be charged.
Phone must be off with battery inside.
Please insert USB cable now...
Detected : MediaTek PreLoader USB VCOM (Android) (COM13)
Boot mode: Preloader
BBCHIP: 321 0 ca00
Using Algo 2.
Phone detected...Please wait
Sending DA agent, please wait...
----------------------------------------------------
BaseBand CPU :MT6735
BaseBand CPU Secure Version : FF
BaseBand CPU Bootloader Version : 01
----------------------------------------------------
INT RAM: 128 KB SDRAM
EXT RAM: 2 GB DRAM
----------------------------------------------------
EMMC: (117Gb+16384Mb) HYNIX 0x484147326505
EMMC FW VERSION: 07:00:00:00:00:00:00:00
EMMC CID: 90014A484147326505 : 00000000000000
EMMC UA SIZE: 0x3ab800000
BOOT STYLE: EMMC BOOT
FULL LENGTH: 0x3ac400000 [14.691 GB]
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detected : MediaTek DA USB VCOM (Android) (COM45)
Partition is damaged or encripted.
This phone have FRP partition.
Partition is damaged or encripted.
IMEI[1]: 359396071508427
IMEI[2]: 359396071508435
Wait untill phone will start charging.
[0]All done.
انفو nck

[™MOHAMED]

الافتتاحيه الاولي ام الثانيه
اعمل فحص للجهاز عن طريق ال CM2

[ana_nasr2000]

الافتتاحيه الاولي

[ana_nasr2000]

Boot Ok!

Processing Miscellaneous test
MSC : BatteryLevel : 3954 mV

[Processing] FlashMemory Read-Write test
[eMMC] : [HYNIX] , e2GA , 0x3AB800000 , 15032 MiB
[eMMC] : CID : 90014A484147326505073564DE6263EF

[eMMC] : MODE : SQ-WR
[FAILED : READONLY] : eMMC state seems as READ-ONLY !!!!

Operation Failed
Elapsed: 00:00:26
Reconnect Power/Cable!

[allttar]

قبل تفليش حاول مقارنة ملف scatter

Tecno_C7_MT6735

[ninja-12]

اعمل تست لداكرة اخي واخبير الزبون قبل كل شيئ اخي لتفادي موت الجهاز