كود:
Selected pinout: GEN2 ISP Pinout
Change EasyJTAG Pinout OK
Selected pinout: GEN2 High Speed Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1683mV pin connected ok
command: 1690mV pin connected ok
data0: 1694mV pin connected ok
data1: 1685mV pin connected ok
data2: 1691mV pin connected ok
data3: 1688mV pin connected ok
data4: 1689mV pin connected ok
data5: 1689mV pin connected ok
data6: 1693mV pin connected ok
data7: 1693mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100464531324D420DB84B683F54C5
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0xD
eMMC NAME: FE12MB , S/N: 3091949631
eMMC NAME (HEX): 464531324D42
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is not yet programmed (clear) or RPMB General failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: FE12MB_3091949631_20190430_0251.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x16b400000] Size: 5.675GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0012D00000 (1.171GB)
---------------------------------------------
Detected USERDATA USERDATA : 0x0065D00000 (5.675GB)
Unable to mount USERDATA , code : 95
Done.
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x16b400000] Size: 5.675GB
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x33aa07200] Size: 12.916GB
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1684mV pin connected ok
command: 1690mV pin connected ok
data0: 1693mV pin connected ok
data1: 1688mV pin connected ok
data2: 1691mV pin connected ok
data3: 1690mV pin connected ok
data4: 1689mV pin connected ok
data5: 1690mV pin connected ok
data6: 1693mV pin connected ok
data7: 1693mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100464531324D420DB84B683F54C5
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0xD
eMMC NAME: FE12MB , S/N: 3091949631
eMMC NAME (HEX): 464531324D42
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is not yet programmed (clear) or RPMB General failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: FE12MB_3091949631_20190430_0252.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x33aa07200] Size: 12.916GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0012D00000 (1.171GB)
---------------------------------------------
Detected USERDATA USERDATA : 0x0065D00000 (12.916GB)
Unable to mount USERDATA , code : 95
Done.
Checking security ...
Selected pinout: GEN2 High Speed Pinout
Change EasyJTAG Pinout OK
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1683mV pin connected ok
command: 1689mV pin connected ok
data0: 1690mV pin connected ok
data1: 1685mV pin connected ok
data2: 1691mV pin connected ok
data3: 1691mV pin connected ok
data4: 1690mV pin connected ok
data5: 1689mV pin connected ok
data6: 1691mV pin connected ok
data7: 1693mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100464531324D420DB84B683F54C5
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0xD
eMMC NAME: FE12MB , S/N: 3091949631
eMMC NAME (HEX): 464531324D42
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is not yet programmed (clear) or RPMB General failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: FE12MB_3091949631_20190430_0307.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x33aa07200] Size: 12.916GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0012D00000 (1.171GB)
---------------------------------------------
Detected USERDATA USERDATA : 0x0065D00000 (12.916GB)
Unable to mount USERDATA , code : 95
Done.
Checking security ...
Running:Repair extCSD...
Z3X EasyJtag Software ver. 3.5.0.1
Skip loading eMMC Addon Firmware
Box IO Level:2800 mV
CLK Rate:21000 kHz
------------Parsing extCSD------------
=============================================
Extended CSD rev 1.7 (MMC 5.0)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]
Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]
Data TAG support [DATA_TAG_SUPPORT: 0x01]
Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]
Tag Resources Size [TAG_RES_SIZE: 0x00]
Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]
Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]
Extended partition attribute support [EXT_SUPPORT: 0x03]
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
------------------------- eMMC v5+ -------------------------
Supported modes [SUPPORTED_MODES: 0x01]
FFU features [FFU_FEATURES: 0x00]
Operation codes timeout [OPERATION_CODE_TIMEOUT: 0x00]
FFU Argument [FFU_ARG: 0x00000000]
Number of FW sectors correctly programmed[NUM_OF_FW_SECT_CORR_PROG: 0]
Vendor proprietary health report:
[VENDOR_PROPRIETARY_HEALTH_REPORT[301]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[300]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[299]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[298]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[297]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[296]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[295]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[294]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[293]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[292]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[291]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[290]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[289]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[288]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[287]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[286]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[285]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[284]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[283]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[282]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[281]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[280]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[279]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[278]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[277]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[276]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[275]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[274]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[273]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[272]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[271]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[270]]:0x00
_(Device life time estimation type B [DEVICE_LIFE_TIME_EST_TYP_B: 0x00]
_(Device life time estimation type B [DEVICE_LIFE_TIME_EST_TYP_A: 0x00]
Pre EOL information [PRE_EOL_INFO: 0x00]
i.e. Not Defined
Optimal read size [OPTIMAL_READ_SIZE: 0x00]
Optimal write size [OPTIMAL_WRITE_SIZE: 0x00]
Optimal trim unit size [OPTIMAL_TRIM_UNIT_SIZE: 0x00]
Device version [DEVICE_VERSION: 0x00 - 0x00]
Firmware version:
[FIRMWARE_VERSION[261]]: 0x00
[FIRMWARE_VERSION[260]]: 0x00
[FIRMWARE_VERSION[259]]: 0x03
[FIRMWARE_VERSION[258]]: 0x00
[FIRMWARE_VERSION[257]]: 0x01
[FIRMWARE_VERSION[256]]: 0x08
[FIRMWARE_VERSION[255]]: 0x00
[FIRMWARE_VERSION[254]]: 0x04
Power class for 200MHz, DDR at VCC= 3.6V [PWR_CL_DDR_200_360: 0x00]
-------------------------------------------------------------
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
Background operations status [BKOPS_STATUS: 0x00]
1st Initialisation Time after programmed sector [INI_TIMEOUT_AP: 0x1e]
Power class for 52MHz, DDR at 3.6V [PWR_CL_DDR_52_360: 0x00]
Power class for 52MHz, DDR at 1.95V [PWR_CL_DDR_52_195: 0x00]
Power class for 200MHz at 3.6V [PWR_CL_200_360: 0x00]
Power class for 200MHz, at 1.95V [PWR_CL_200_195: 0x00]
Minimum Performance for 8bit at 52MHz in DDR mode:
[MIN_PERF_DDR_W_8_52: 0x00]
[MIN_PERF_DDR_R_8_52: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x20]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x10]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x00e90000]
Minimum Write Performance for 8bit:
[MIN_PERF_W_8_52: 0x00]
[MIN_PERF_R_8_52: 0x00]
[MIN_PERF_W_8_26_4_52: 0x00]
[MIN_PERF_R_8_26_4_52: 0x00]
Minimum Write Performance for 4bit:
[MIN_PERF_W_4_26: 0x00]
[MIN_PERF_R_4_26: 0x00]
Power classes registers:
[PWR_CL_26_360: 0x00]
[PWR_CL_52_360: 0x00]
[PWR_CL_26_195: 0x00]
[PWR_CL_52_195: 0x00]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x05]
I/O Driver Strength [DRIVER_STRENGTH: 0x3f]
Card Type [CARD_TYPE: 0x57]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x08]
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x10
Power ReadOnly locking: possible
Permanent ReadOnly locking: not possible
Read Only lock status: not locked
User area write protection register [USER_WP]: 0x10
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x04
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x04
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0001d2
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size
[GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Periodic Wake-up [PERIODIC_WAKEUP]: 0x00
Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01
Native sector size [NATIVE_SECTOR_SIZE]: 0x00
Sector size emulation [USE_NATIVE_SECTOR]: 0x00
Sector size [DATA_SECTOR_SIZE]: 0x00
1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00
Class 6 commands control [CLASS_6_CTRL]: 0x00
Number of addressed group to be released[DYNCAP_NEEDED]: 0x00
Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000
Exception events status [EXCEPTION_EVENTS_STATUS]: 0x0000
Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000
Packed command status [PACKED_COMMAND_STATUS]: 0x00
Packed command failure index [PACKED_FAILURE_INDEX]: 0x00
Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00
Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00
------------Done parsing------------
Writing as extCSD 5.1
Done.
Checking security ...
Z3X EasyJtag Software ver. 3.5.0.1
Skip loading eMMC Addon Firmware
Input file : D:\EMMC\SAMSUNG\i9060i\New folder\EMMC_QNW00M_ROM1_000000000000_000040000000.bin
Writing 0040000000 bytes to 0000000000... ROM1 (USER ROM)
Full Verify Enabled!
Done, time taken: 113 sec. Average Write Speed: 9428 kB/s
Checking security ...
Z3X EasyJtag Software ver. 3.5.0.1
Skip loading eMMC Addon Firmware
Input file : D:\EMMC\SAMSUNG\i9060i\New folder\EMMC_QNW00M_ROM2_000000000000_000000400000.bin
Writing 0000400000 bytes to 0000000000 ...ROM2 (BOOT1 ROM)
Full Verify Enabled!
Done, time taken: 0.471 sec. Average Write Speed: 8962 kB/s
Checking security ...
Z3X EasyJtag Software ver. 3.5.0.1
Skip loading eMMC Addon Firmware
Input file : D:\EMMC\SAMSUNG\i9060i\New folder\EMMC_QNW00M_ROM3_000000000000_000000400000.bin
Writing 0000400000 bytes to 0000000000 ...ROM3 (BOOT2 ROM)
Full Verify Enabled!
Done, time taken: 0.446 sec. Average Write Speed: 9279 kB/s
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1678mV pin connected ok
command: 1687mV pin connected ok
data0: 1688mV pin connected ok
data1: 1684mV pin connected ok
data2: 1688mV pin connected ok
data3: 1688mV pin connected ok
data4: 1685mV pin connected ok
data5: 1685mV pin connected ok
data6: 1687mV pin connected ok
data7: 1689mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 150100464531324D420DB84B683F54C5
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 05/2017 Rev.0xD
eMMC NAME: FE12MB , S/N: 3091949631
eMMC NAME (HEX): 464531324D42
EMMC ROM1 (Main User Data) Capacity: 14910 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 kB
EMMC RPMB is not yet programmed (clear) or RPMB General failure
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.8 (MMC 5.1)
Boot configuration [PARTITION_CONFIG: 0x08] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x08.
H/W reset function [RST_N_FUNCTION]: 0x01
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: FE12MB_3091949631_20190430_0309.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (SBOOT) [0x400000 0x200000] Size: 2.0MB
P1 (SBOOT2) [0x600000 0x200000] Size: 2.0MB
P2 (WFIXNV1) [0x800000 0x100000] Size: 1.0MB
P3 (WFIXNV2) [0x900000 0x100000] Size: 1.0MB
P4 (TDFIXNV1) [0xa00000 0x100000] Size: 1.0MB
P5 (TDFIXNV2) [0xb00000 0x100000] Size: 1.0MB
P6 (WDSP) [0xc00000 0x400000] Size: 4.0MB
P7 (MODEM) [0x1000000 0x800000] Size: 8.0MB
P8 (MODEM2) [0x1800000 0x800000] Size: 8.0MB
P9 (TDDSP) [0x2000000 0x400000] Size: 4.0MB
P10 (FOTA_SIG) [0x2400000 0x100000] Size: 1.0MB
P11 (WRUNTIMENV1) [0x2500000 0x100000] Size: 1.0MB
P12 (WRUNTIMENV2) [0x2600000 0x100000] Size: 1.0MB
P13 (TDRUNTIMENV1) [0x2700000 0x100000] Size: 1.0MB
P14 (TDRUNTIMENV2) [0x2800000 0x100000] Size: 1.0MB
P15 (PARAM) [0x2900000 0x200000] Size: 2.0MB
P16 (EFS) [0x2b00000 0x1400000] Size: 20.0MB
P17 (PRODNV) [0x3f00000 0x500000] Size: 5.0MB
P18 (RESERVED2) [0x4400000 0x100000] Size: 1.0MB
P19 (KERNEL) [0x4500000 0x1000000] Size: 16.0MB
P20 (RECOVERY) [0x5500000 0x1000000] Size: 16.0MB
P21 (CSC) [0x6500000 0xc800000] Size: 200.0MB
P22 (SYSTEM) [0x12d00000 0x4b000000] Size: 1.171GB
P23 (HIDDEN) [0x5dd00000 0x8000000] Size: 128.0MB
P24 (USERDATA) [0x65d00000 0x16b400000] Size: 5.675GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0012D00000 (1.171GB)
Build ID: KTU84P
Display Build ID: KTU84P.I9060IXMU0AOG2
Release Incremental ID: I9060IXMU0AOG2
Release Base ID: 4.4.4
Device Model: GT-I9060I
Device Name: grandneove3gxx
Architecture ABI: armeabi-v7a
Device manufacturer: samsung
Device Platform: sc8830
Product ID: grandneove3g
Build Description: grandneove3gxx-user 4.4.4 KTU84P I9060IXMU0AOG2 release-keys
Samsung CPU: sc7730s
---------------------------------------------
Detected USERDATA USERDATA : 0x0065D00000 (5.675GB)
Unable to mount USERDATA , code : 95
Done.
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1716mV pin connected ok
command: 1728mV pin connected ok
data0: 1729mV pin connected ok
data1: 1724mV pin connected ok
data2: 1727mV pin connected ok
data3: 1729mV pin connected ok
data4: 1728mV pin connected ok
data5: 1729mV pin connected ok
data6: 1723mV pin connected ok
data7: 1728mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 15010038574D423352004156D3DC91F9
eMMC CSD : D02701320F5903FFF6DBFFEF8E406069
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 09/2014 Rev.0x0
eMMC NAME: 8WMB3R , S/N: 1096209372
eMMC NAME (HEX): 38574D423352
IC Name: Samsung , KLM8G1WEMB-B031/8GB @FBGA153
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC RPMB is programmed and written 15 times
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: 8WMB3R_1096209372_20190430_0311.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (APNHLOS) [0x400000 0xe00000] Size: 14.0MB
P1 (MODEM) [0x1200000 0x31c0000] Size: 49.750MB
P2 (SBL1) [0x43c0000 0x80000] Size: 512.0KB
P3 (DBI) [0x4440000 0x8000] Size: 32.0KB
P4 (DDR) [0x4448000 0x8000] Size: 32.0KB
P5 (ABOOT) [0x4450000 0x200000] Size: 2.0MB
P6 (RPM) [0x4650000 0x80000] Size: 512.0KB
P7 (TZ) [0x46d0000 0x80000] Size: 512.0KB
P8 (PAD) [0x4750000 0x100000] Size: 1.0MB
P9 (PARAM) [0x4850000 0xa00000] Size: 10.0MB
P10 (EFS) [0x5250000 0xe00000] Size: 14.0MB
P11 (MODEMST1) [0x6050000 0x300000] Size: 3.0MB
P12 (MODEMST2) [0x6350000 0x300000] Size: 3.0MB
P13 (BOOT) [0x6650000 0xa00000] Size: 10.0MB
P14 (RECOVERY) [0x7050000 0xa00000] Size: 10.0MB
P15 (FOTA) [0x7a50000 0xa00000] Size: 10.0MB
P16 (BACKUP) [0x8450000 0x6fdc00] Size: 6.991MB
P17 (FSG) [0x8b4dc00 0x300000] Size: 3.0MB
P18 (FSC) [0x8e4dc00 0x400] Size: 1.0KB
P19 (SSD) [0x8e4e000 0x2000] Size: 8.0KB
P20 (PERSIST) [0x8e50000 0x800000] Size: 8.0MB
P21 (SYSTEM) [0x9650000 0x6f400000] Size: 1.738GB
P22 (CACHE) [0x78a50000 0xd000000] Size: 208.0MB
P23 (HIDDEN) [0x85a50000 0x1400000] Size: 20.0MB
P24 (USERDATA) [0x86e50000 0x14b1abe00] Size: 5.172GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0009650000 (1.738GB)
Build ID: KOT49H
Display Build ID: KOT49H.G7102XXUBNH5
Release Incremental ID: G7102XXUBNH5
Release Base ID: 4.4.2
Device Model: SM-G7102
Device Name: ms013gxx
Architecture ABI: armeabi-v7a
Device manufacturer: samsung
Device Platform: msm8226
Product ID: ms013g
Build Description: ms013gxx-user 4.4.2 KOT49H G7102XXUBNH5 release-keys
Samsung CPU: MSM8226
---------------------------------------------
Detected USERDATA USERDATA : 0x0086E50000 (5.172GB)
Gesture HASH :B7E5F598C4F386D97C8FCD082694584792558C02
Done.
Checking security ...
Running:SAMSUNG: Remove Write Protection...
Z3X EasyJtag Software ver. 3.5.0.1
Skip loading eMMC Addon Firmware
Box IO Level:2800 mV
CLK Rate:21000 kHz
Removing write protection...
Done.
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1717mV pin connected ok
command: 1724mV pin connected ok
data0: 1728mV pin connected ok
data1: 1724mV pin connected ok
data2: 1726mV pin connected ok
data3: 1728mV pin connected ok
data4: 1728mV pin connected ok
data5: 1729mV pin connected ok
data6: 1726mV pin connected ok
data7: 1728mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 15010038574D423352004156D3DC91F9
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 09/2014 Rev.0x0
eMMC NAME: 8WMB3R , S/N: 1096209372
eMMC NAME (HEX): 38574D423352
IC Name: Samsung , KLM8G1WEMB-B031/8GB @FBGA153
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC RPMB is programmed and written 15 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: 8WMB3R_1096209372_20190430_0311.extcsd
Partition info successfully found
Found Data areas (firmware parts) count is: 25
---------------------------------------------
P0 (APNHLOS) [0x400000 0xe00000] Size: 14.0MB
P1 (MODEM) [0x1200000 0x31c0000] Size: 49.750MB
P2 (SBL1) [0x43c0000 0x80000] Size: 512.0KB
P3 (DBI) [0x4440000 0x8000] Size: 32.0KB
P4 (DDR) [0x4448000 0x8000] Size: 32.0KB
P5 (ABOOT) [0x4450000 0x200000] Size: 2.0MB
P6 (RPM) [0x4650000 0x80000] Size: 512.0KB
P7 (TZ) [0x46d0000 0x80000] Size: 512.0KB
P8 (PAD) [0x4750000 0x100000] Size: 1.0MB
P9 (PARAM) [0x4850000 0xa00000] Size: 10.0MB
P10 (EFS) [0x5250000 0xe00000] Size: 14.0MB
P11 (MODEMST1) [0x6050000 0x300000] Size: 3.0MB
P12 (MODEMST2) [0x6350000 0x300000] Size: 3.0MB
P13 (BOOT) [0x6650000 0xa00000] Size: 10.0MB
P14 (RECOVERY) [0x7050000 0xa00000] Size: 10.0MB
P15 (FOTA) [0x7a50000 0xa00000] Size: 10.0MB
P16 (BACKUP) [0x8450000 0x6fdc00] Size: 6.991MB
P17 (FSG) [0x8b4dc00 0x300000] Size: 3.0MB
P18 (FSC) [0x8e4dc00 0x400] Size: 1.0KB
P19 (SSD) [0x8e4e000 0x2000] Size: 8.0KB
P20 (PERSIST) [0x8e50000 0x800000] Size: 8.0MB
P21 (SYSTEM) [0x9650000 0x6f400000] Size: 1.738GB
P22 (CACHE) [0x78a50000 0xd000000] Size: 208.0MB
P23 (HIDDEN) [0x85a50000 0x1400000] Size: 20.0MB
P24 (USERDATA) [0x86e50000 0x14b1abe00] Size: 5.172GB
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x0009650000 (1.738GB)
Build ID: KOT49H
Display Build ID: KOT49H.G7102XXUBNH5
Release Incremental ID: G7102XXUBNH5
Release Base ID: 4.4.2
Device Model: SM-G7102
Device Name: ms013gxx
Architecture ABI: armeabi-v7a
Device manufacturer: samsung
Device Platform: msm8226
Product ID: ms013g
Build Description: ms013gxx-user 4.4.2 KOT49H G7102XXUBNH5 release-keys
Samsung CPU: MSM8226
---------------------------------------------
Detected USERDATA USERDATA : 0x0086E50000 (5.172GB)
Gesture HASH :B7E5F598C4F386D97C8FCD082694584792558C02
Done.
Checking security ...
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1718mV pin connected ok
command: 1727mV pin connected ok
data0: 1730mV pin connected ok
data1: 1728mV pin connected ok
data2: 1727mV pin connected ok
data3: 1729mV pin connected ok
data4: 1730mV pin connected ok
data5: 1729mV pin connected ok
data6: 1727mV pin connected ok
data7: 1727mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 15010038574D423352004156D3DC91F9
eMMC CSD : D02701320F5903FFF6DBFFEF8E40400D
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 09/2014 Rev.0x0
eMMC NAME: 8WMB3R , S/N: 1096209372
eMMC NAME (HEX): 38574D423352
IC Name: Samsung , KLM8G1WEMB-B031/8GB @FBGA153
EMMC ROM1 (Main User Data) Capacity: 7456 MB , 0xE90000 pages , 0x1D2000000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC RPMB is programmed and written 15 times
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Partition info successfully found
------ Android information ------
Detected LINUX(Android) CACHE : 0x0078A50000 (208.0MB)
Erasing...
Done.
Detected LINUX(Android) USERDATA : 0x0086E50000 (5.172GB)
Erasing...
Done.
---------------------------------------------
Done.
Checking security ...
Z3X EasyJtag Software ver. 3.5.0.1
Loading eMMC GEN2 Firmware... IO: 2800 mV
Initial pull results:
clock: 1717mV pin connected ok
command: 1727mV pin connected ok
data0: 1729mV pin connected ok
data1: 1726mV pin connected ok
data2: 1728mV pin connected ok
data3: 1729mV pin connected ok
data4: 1730mV pin connected ok
data5: 1728mV pin connected ok
data6: 1727mV pin connected ok
data7: 1727mV pin connected ok
Box S/N: B052D701B8273134, ,FW Ver.: 02.38
Box IO Level:2800 mV
CLK Rate:21000 kHz
Bus Width:8bit,SDR
HiPower mode is off!
---------- eMMC Device Information ----------
eMMC CID : 15010038574D423352004156D3DC91F9
eMMC CSD : D02701320F5903FFF6DBFFEF8E406069
eMMC Manufacturer ID: 0015 , OEM ID: 0100
eMMC Date: 09/2014 Rev.0x0
eMMC NAME: 8WMB3R , S/N: 1096209372
eMMC NAME (HEX): 38574D423352
IC Name: Samsung , KLM8G1WEMB-B031/8GB @FBGA153
EMMC ROM1 (Main User Data) Capacity: 7456 MB , 0xE90000 pages , 0x1D2000000 bytes
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC RPMB is programmed and written 15 times
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity WP group size [HC_WP_GRP_SIZE: 0x00004000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Partition info successfully found
------ Android information ------
Detected LINUX(Android) CACHE : 0x0078A50000 (208.0MB)
Read EXT fs info
Read EXT fs info
Created filesystem with parameters:
Size: 22518393277644867
Block size: 22518393281118322
Blocks per group: 7471207
Inodes per group: 7143521
Inode size: 4587552
Inodes: 7077993
Label:
Formatting EXT fs...
تغيير وزيادة الذاكرة الداخلية لجهاز سامسونج جراند نيو بلس i9060i by smart fix with great easy jtag plus
.gif)
المفضلات