توقف جهاز Nokia TA 1017 بعد الفلاش
السلام عليكم ورحمة الله تعالى و بركاتهمعلومات الهاتف
ممكن مساعدة توقف جهاز Nokia TA-1017
كود:Operation : Identify [ v1.12 ] 1. Make sure device is powered off. Power off, if need. Wait 10 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : Care Suite USB Serial Port (COM53) MODE : NOKIA USB SERIAL PORT : 53 BROM : Init BROM BROM init passed! CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001 BROM : SECCFG : 0x00000007 BROM : NOKIA USB SERIAL BROM : 0x05 BL : 0x00 BROM : MEID : 100CFFAC95D9A6C0682951F8D5E9CADE BROM : Run BootLoader ... BOOT : Run BL ver. 01 BOOT : 0x05 BL : 0x01 BOOT : WD : 0005 BOOT : RTC : Setup ... BOOT : RTC : 000E BOOT : PRJ : KESA61A.11.02.11.p1 BOOT : SWR : 11.02.11 BOOT : BDDS : 30 BOOT : PSRM : Init BOOT : PSRM : 0003 Boot done! SWVer : KESA61A.11.02.11.p1 FLASH : 00EF : 0060 : 0017 : 0000 BBSN : 100CFFAC95D9A6C0682951F8D5E9CADE PRDC : 059Z209 IMEI[1] : 35************* IMEI[2] : 35************* NCK : 20 digits PROV : 24407000 Saved as : 35************.mtsec Saved to : I:\InfinityBox\BEST2\Backup\
لوغ التفليش
كود:Operation : Write FirmWare [ v1.12 ] Setting : UserData erase : False Setting : LangPack Only : False 1. Make sure device is powered off. Power off, if need. Wait 10 seconds after 2. Insert USB cable in phone Waiting for device connection ... PTFN : Care Suite USB Serial Port (COM53) MODE : NOKIA USB SERIAL PORT : 53 BROM : Init BROM BROM init passed! CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001 BROM : SECCFG : 0x00000007 BROM : NOKIA USB SERIAL BROM : 0x05 BL : 0x00 BROM : MEID : 100CFFAC95D9A6C0682951F8D5E9CADE BROM : Run BootLoader ... BOOT : Run BL ver. 01 BOOT : 0x05 BL : 0x01 BOOT : WD : 0005 BOOT : RTC : Setup ... BOOT : RTC : 000E BOOT : PRJ : KESA61A.11.02.11.p1 BOOT : SWR : 11.02.11 AGENT : Look for suitable BootChain in DA ... AGENT : DEFAULT AUTO AGENT : Found MT6261 AGENT : KESA61A.11.02.11.p1 BOOT : Sending 1st DA ... BOOT : DA sent BOOT : Transfer control to DA ... DA : Sync Passed! DA : Authentification pass! DA : Agent : v03.02 on BBID : 0x8E NOR: 00C2 : 0025 : 0037 : 0000 NOR: [MX] MX25U6435E NOR: TSIZE : 0x00800000 [ 8,00 MB ] PSIZE : 0x00800000 [ 8,00 MB ] STYPE : 0x00000000 FLOTP : DA_NOR_OTP_EXIST STATUS : OK BSTYLE : SF_FLASH_BOOT Boot done! VPL SoftwareVersion : 11.02.11 [TA-1017] DEV SoftwareVersion : 11.02.11 SWInfo compare result : SAME Load FlashSet : MROM : TA-1017_ROM_eMP_11.02.11 LANG : TA-1017_LANG_PACK_ROM_IC_eMP_11.02.11_001 CUST : TA-1017_CUSTPACK_ROM_IC_MEA_MA_eMP_11.02.11_001 JUMP : TA-1017_JUMP_TABLE_IC_MEA_MA_eMP_11.02.11_001 VIVA : TA-1017_VIVA_eMP_11.02.11 Prepare FlashSet : DCR : TA-1017_ROM_eMP_11.02.11 DCR : TA-1017_LANG_PACK_ROM_IC_eMP_11.02.11_001 DCR : TA-1017_CUSTPACK_ROM_IC_MEA_MA_eMP_11.02.11_001 DCR : TA-1017_JUMP_TABLE_IC_MEA_MA_eMP_11.02.11_001 DCR : TA-1017_VIVA_eMP_11.02.11 Prepare Target SDS : OK : 0x007F8000 : 0x00008000 Erase Target Flash Erase done! Write Target Flash Write : TA-1017_ROM_eMP_11.02.11 Write : TA-1017_LANG_PACK_ROM_IC_eMP_11.02.11_001 Write : TA-1017_CUSTPACK_ROM_IC_MEA_MA_eMP_11.02.11_001 Write : TA-1017_JUMP_TABLE_IC_MEA_MA_eMP_11.02.11_001 Write : TA-1017_VIVA_eMP_11.02.11 Flash_Write ERROR : DA_CBR_NOT_FOUND Error : Flashing failed! Make sure device HW is in normal condition, check battery and cable!
المشاركة الأصلية كتبت بواسطة mena_what
المفضلات