المشاركة الأصلية كتبت بواسطة Rodwan I.A
كيفية حل مشكلة ال contact service لاجهزة نوكيا TA xxxx
اولا نفتح واجهة ال Best NK2 ver. 1.08
ومنها نختار (Nokia MTK (FP
ثم نختار موديل الجهاز من Select RM/TA
ثم نضغط على Identify ونوصل الجهاز وهو مغلق
بال USB حتى يتم التعرف على الجهاز.
نعلم على Factory Reset
ونضغط على Write FW دون ان نضيف اي ملف للتفليش.
كود:
Operation : Identify [ v1.08 ]
1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : Care Suite USB Serial Port (COM15)
MODE : NOKIA USB SERIAL
PORT : 15
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 8083D6D9CB5992735A54EC189575B0FE
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.10.02.11.p1
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003
Boot done!
SWVer : N103.10.02.11.p1
FLASH : 00C2 : 0025 : 0036 : 0000
BBSN : 8083D6D9CB5992735A54EC189575B0FE
PRDC : 059Z107
IMEI[1] : 354495099044087
IMEI[2] : 354500094044089
Done!
Elapsed: 00:01:00
Reconnect Power/Cable!
Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False
1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : Care Suite USB Serial Port (COM15)
MODE : NOKIA USB SERIAL
PORT : 15
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 8083D6D9CB5992735A54EC189575B0FE
BROM : Run BootLoader ...
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ...
BOOT : RTC : 000E
BOOT : PRJ : N103.10.02.11.p1
AGENT : Look for suitable BootChain in DA ...
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : N103.10.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ...
DA : Agent : v03.02 on BBID : 0x8E
NOR: 00EF : 0070 : 0016 : 0000
NOR: [Winbond] SF_W25Q32JV
NOR:
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST
STATUS : OK
BSTYLE : SF_FLASH_BOOT
Boot done!
Load FlashSet :
Prepare FlashSet :
Prepare Target
SDS : OK : 0x003F8000 : 0x00008000
FFS Format Ok!
Erase Target Flash
Erase done!
Write Target Flash
100 % ok
كيفية حل مشكلة ال contact service لاجهزة نوكيا TA xxxx
المفضلات