كيفية حل مشكلة ال contact service لاجهزة نوكيا TA xxxx


اولا نفتح واجهة ال Best NK2 ver. 1.08

ومنها نختار (Nokia MTK (FP

ثم نختار موديل الجهاز من Select RM/TA

ثم نضغط على Identify ونوصل الجهاز وهو مغلق
بال USB حتى يتم التعرف على الجهاز.

نعلم على Factory Reset

ونضغط على Write FW دون ان نضيف اي ملف للتفليش.

كود:


Operation : Identify [ v1.08 ]
1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : Care Suite USB Serial Port (COM15)
MODE : NOKIA USB SERIAL
PORT : 15
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 8083D6D9CB5992735A54EC189575B0FE
BROM : Run BootLoader ... 
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ... 
BOOT : RTC : 000E
BOOT : PRJ : N103.10.02.11.p1
BOOT : BDDS : 30
BOOT : PSRM : Init
BOOT : PSRM : 0003
Boot done!
SWVer : N103.10.02.11.p1
FLASH : 00C2 : 0025 : 0036 : 0000
BBSN : 8083D6D9CB5992735A54EC189575B0FE
PRDC : 059Z107
IMEI[1] : 354495099044087
IMEI[2] : 354500094044089
Done!
Elapsed: 00:01:00
Reconnect Power/Cable!
Operation : Write FirmWare [ v1.08 ]
Setting : UserData erase : True
Setting : LangPack Only : False
1. Make sure device is powered off. Power off, if need. Wait 10 seconds after
2. Insert USB cable in phone
Waiting for device connection ...
PTFN : Care Suite USB Serial Port (COM15)
MODE : NOKIA USB SERIAL
PORT : 15
BROM : Init BROM
BROM init passed!
CHIP : MT6261 , SBID : 0xCB01 , HWVR : 0x8000 , SWVR : 0x0001
BROM : SECCFG : 0x00000007
BROM : NOKIA USB SERIAL
BROM : 0x05 BL : 0x00
BROM : MEID : 8083D6D9CB5992735A54EC189575B0FE
BROM : Run BootLoader ... 
BOOT : Run BL ver. 01
BOOT : 0x05 BL : 0x01
BOOT : WD : 0005
BOOT : RTC : Setup ... 
BOOT : RTC : 000E
BOOT : PRJ : N103.10.02.11.p1
AGENT : Look for suitable BootChain in DA ... 
AGENT : DEFAULT AUTO
AGENT : Found MT6261
AGENT : N103.10.02.11.p1
BOOT : Sending 1st DA ...
BOOT : DA sent
BOOT : Transfer control to DA ... 
DA : Agent : v03.02 on BBID : 0x8E
NOR: 00EF : 0070 : 0016 : 0000
NOR: [Winbond] SF_W25Q32JV
NOR: 
TSIZE : 0x00400000 [ 4.00 MB ]
PSIZE : 0x00400000 [ 4.00 MB ]
STYPE : 0x00000000
FLOTP : DA_NOR_OTP_EXIST
STATUS : OK
BSTYLE : SF_FLASH_BOOT
Boot done!
Load FlashSet : 
Prepare FlashSet : 
Prepare Target 
SDS : OK : 0x003F8000 : 0x00008000
FFS Format Ok!
Erase Target Flash 
Erase done!
Write Target Flash
100 % ok