الثالثة عند كتابة الرومات EasyJtag Suite Classic ver.: 2.5.1.0 / wxWidgets 3.1.0-W-U started.OS ver.: Windows 7 (build 7601, Service Pack 1). Admin rights OK
undefined
Android Explorer ver.: 1.0.0.24
eMMC ODIN ver.: 1.0.11.3
Successfully connected to box on COM73
Box S/N: 101009179BED7E59, ,FW Ver.: 01.58
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.1.0, are OK
Z3X Card Serial : AA5A-3819 , ver: 22
Z3X Card Activation [LG] : NOT ACTIVATED
Z3X Card Activation [SAMS] : ACTIVATED
Z3X Card Activation [JTAG] : ACTIVATED
Compression is ON
Z3X EasyJtag Software ver. 2.5.1.0
Loading eMMC GEN1 Firmware... IO: 1800 mV
Box S/N: 101009179BED7E59, ,FW Ver.: 01.58
CMD Pullup Level:1866 mV
CMD Active Level:1856 mV
Box IO Level:1800 mV
CLK Rate:14000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------
EMMC CID : 150100514E5730304D00E58AC22F91BE
EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2014 Rev.0x0
EMMC NAME: QNW00M , S/N: 3851076143
EMMC NAME (HEX): 514E5730304D00
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QNW00M_3851076143_20180804_2003.extcsd
Done.
extCSD Are not selected , skip writing extCSD
ROM1 Are not selected , skip writing ROM1
ROM2 Are not selected , skip writing ROM2
ROM3 Are not selected , skip writing ROM3
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM1_000000000000_000010000000.bin
Autodetected RAW data
Warning! Disk size is smaller than the main header indicates! Loading
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!
Found ROM2 and automatically selected.
Found ROM3 and automatically selected.
Found EXT CSD and automatically selected.
Real (Hardware) Disk/Image size: 80000 sectors 256.0 MiB
Soft (Partitioned) Disk/Image size: E8FFBC sectors 7.3 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
First usable sector: 34
Last usable sector: 15269854
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM2_000000000000_000000400000.bin
File successefuly loaded!
Found ROM3 and automatically selected.
Found EXT CSD and automatically selected.
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM3_000000000000_000000400000.bin
File successefuly loaded!
Found ROM2 and automatically selected.
Found ROM1 and automatically selected.
Found EXT CSD and automatically selected.
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM1_000000000000_000010000000.bin
Autodetected RAW data
Warning! Disk size is smaller than the main header indicates! Loading
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Partition info successfully found
Linux partitions is not found in image...
File successefuly loaded!
Found ROM2 and automatically selected.
Found ROM3 and automatically selected.
Found EXT CSD and automatically selected.
Real (Hardware) Disk/Image size: 80000 sectors 256.0 MiB
Soft (Partitioned) Disk/Image size: E8FFBC sectors 7.3 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
First usable sector: 34
Last usable sector: 15269854
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM2_000000000000_000000400000.bin
File successefuly loaded!
Found ROM3 and automatically selected.
Found EXT CSD and automatically selected.
Checking NAND Image : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM3_000000000000_000000400000.bin
File successefuly loaded!
Found ROM2 and automatically selected.
Found ROM1 and automatically selected.
Found EXT CSD and automatically selected.
Compression is ON
Z3X EasyJtag Software ver. 2.5.1.0
Loading eMMC GEN1 Firmware... IO: 1800 mV
Box S/N: 101009179BED7E59, ,FW Ver.: 01.58
CMD Pullup Level:1876 mV
CMD Active Level:1876 mV
Box IO Level:1800 mV
CLK Rate:14000 khz
HiPower mode is ON!
---------- eMMC Device Information ----------
EMMC CID : 150100514E5730304D00E58AC22F91BE
EMMC CSD : D02701320F5903FFF6DBFFEF8E40400C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 09/2014 Rev.0x0
EMMC NAME: QNW00M , S/N: 3851076143
EMMC NAME (HEX): 514E5730304D00
EMMC ROM1 (Main User Data) Capacity: 7456 MB
EMMC ROM2 (Boot Partition 1) Capacity: 4096 kB
EMMC ROM3 (Boot Partition 2) Capacity: 4096 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 512 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
EMMC Password Locked: No
Extended CSD rev 1.7 (MMC 5.0)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x00000000]
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
---------------------------------------------
Backup saved: QNW00M_3851076143_20180804_2008.extcsd
Caution: invalid backup GPT header, but valid main header!
EFI Table CRC Check FAIL.
Warning! One or more CRCs don't match. You should repair the disk!
Partition table scan:
GPT: damaged
Caution: Found protective or hybrid MBR and corrupt GPT.
Real (Hardware) Disk/Image size: E90000 sectors 7.3 GiB
Soft (Partitioned) Disk/Image size: 3E2FDD sectors 1.9 GiB
Logical sector size: 0x200 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
First usable sector: 34
Last usable sector: 4075519
Found Data areas (firmware parts) count is: 27
Partition info successfully found
---------------------------------------------
P0 (APNHLOS) [0x400000 0xf00000] Size: 15.0MB
P1 (MODEM) [0x1300000 0x3970000] Size: 57.437MB
P2 (SBL1) [0x4c70000 0x80000] Size: 512.0KB
P3 (DDR) [0x4cf0000 0x8000] Size: 32.0KB
P4 (ABOOT) [0x4cf8000 0x200000] Size: 2.0MB
P5 (RPM) [0x4ef8000 0x80000] Size: 512.0KB
P6 (QSEE) [0x4f78000 0x80000] Size: 512.0KB
P7 (QHEE) [0x4ff8000 0x80000] Size: 512.0KB
P8 (FSG) [0x5078000 0x300000] Size: 3.0MB
P9 (SEC) [0x5378000 0x4000] Size: 16.0KB
P10 (PAD) [0x537c000 0xa84000] Size: 10.515MB
P11 (PARAM) [0x5e00000 0xa00000] Size: 10.0MB
P12 (EFS) [0x6800000 0xe00000] Size: 14.0MB
P13 (MODEMST1) [0x7600000 0x300000] Size: 3.0MB
P14 (MODEMST2) [0x7900000 0x300000] Size: 3.0MB
P15 (BOOT) [0x7c00000 0xd00000] Size: 13.0MB
P16 (RECOVERY) [0x8900000 0xf00000] Size: 15.0MB
P17 (FOTA) [0x9800000 0x500400] Size: 5.0MB
P18 (BACKUP) [0x9d00400 0x6fdc00] Size: 6.991MB
P19 (FSC) [0xa3fe000 0x300000] Size: 3.0MB
P20 (SSD) [0xa6fe000 0x2000] Size: 8.0KB
P21 (PERSIST) [0xa700000 0x800000] Size: 8.0MB
P22 (PERSDATA) [0xaf00000 0x900000] Size: 9.0MB
P23 (SYSTEM) [0xb800000 0x5d800000] Size: 1.460GB
P24 (CACHE) [0x69000000 0x12c00000] Size: 300.0MB
P25 (HIDDEN) [0x7bc00000 0xa00000] Size: 10.0MB
P26 (USERDATA) [0x7c600000 0] Size: 0.0B
------ Android information ------
Detected LINUX(Android) SYSTEM : 0x000B800000 (1.460GB)
Unable to read prop.plist , code 2
---------------------------------------------
Done.
Processing file...D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\QNW00M_EE8BC668_20170831_121517.extcsd
Processing file...D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM1_000000000000_000010000000.bin
Processing file...D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM2_000000000000_000000400000.bin
Processing file...D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM3_000000000000_000000400000.bin
Running:Repair extCSD...
Z3X EasyJtag Software ver. 2.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1876 mV
CMD Active Level:1876 mV
Box IO Level:1800 mV
CLK Rate:14000 khz
------------Parsing extCSD------------
=============================================
Extended CSD rev 1.7 (MMC 5.0)
=============================================
Card Supported Command sets [S_CMD_SET: 0x01]
HPI Features [HPI_FEATURE: 0x01]:
implementation based on CMD13
Background operations support [BKOPS_SUPPORT: 0x01]
Max Packet Read Cmd [MAX_PACKED_READS: 0x3f]
Max Packet Write Cmd [MAX_PACKED_WRITES: 0x3f]
Data TAG support [DATA_TAG_SUPPORT: 0x01]
Data TAG Unit Size [TAG_UNIT_SIZE: 0x04]
Tag Resources Size [TAG_RES_SIZE: 0x00]
Context Management Capabilities [CONTEXT_CAPABILITIES: 0x05]
Large Unit Size [LARGE_UNIT_SIZE_M1: 0x07]
Extended partition attribute support [EXT_SUPPORT: 0x03]
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
------------------------- eMMC v5+ -------------------------
Supported modes [SUPPORTED_MODES: 0x01]
FFU features [FFU_FEATURES: 0x00]
Operation codes timeout [OPERATION_CODE_TIMEOUT: 0x00]
FFU Argument [FFU_ARG: 0x00000000]
Number of FW sectors correctly programmed[NUM_OF_FW_SECT_CORR_PROG: 0]
Vendor proprietary health report:
[VENDOR_PROPRIETARY_HEALTH_REPORT[301]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[300]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[299]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[298]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[297]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[296]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[295]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[294]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[293]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[292]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[291]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[290]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[289]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[288]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[287]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[286]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[285]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[284]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[283]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[282]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[281]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[280]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[279]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[278]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[277]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[276]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[275]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[274]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[273]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[272]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[271]]:0x00
[VENDOR_PROPRIETARY_HEALTH_REPORT[270]]:0x00
_(Device life time estimation type B [DEVICE_LIFE_TIME_EST_TYP_B: 0x00]
_(Device life time estimation type B [DEVICE_LIFE_TIME_EST_TYP_A: 0x00]
Pre EOL information [PRE_EOL_INFO: 0x00]
i.e. Not Defined
Optimal read size [OPTIMAL_READ_SIZE: 0x00]
Optimal write size [OPTIMAL_WRITE_SIZE: 0x00]
Optimal trim unit size [OPTIMAL_TRIM_UNIT_SIZE: 0x00]
Device version [DEVICE_VERSION: 0x00 - 0x00]
Firmware version:
[FIRMWARE_VERSION[261]]: 0x00
[FIRMWARE_VERSION[260]]: 0x00
[FIRMWARE_VERSION[259]]: 0x03
[FIRMWARE_VERSION[258]]: 0x00
[FIRMWARE_VERSION[257]]: 0x01
[FIRMWARE_VERSION[256]]: 0x08
[FIRMWARE_VERSION[255]]: 0x00
[FIRMWARE_VERSION[254]]: 0x00
Power class for 200MHz, DDR at VCC= 3.6V [PWR_CL_DDR_200_360: 0x00]
-------------------------------------------------------------
Generic CMD6 Timer [GENERIC_CMD6_TIME: 0x0a]
Power off notification [POWER_OFF_LONG_TIME: 0x3c]
Cache Size [CACHE_SIZE] is 65536 KiB
Background operations status [BKOPS_STATUS: 0x00]
1st Initialisation Time after programmed sector [INI_TIMEOUT_AP: 0x1e]
Power class for 52MHz, DDR at 3.6V [PWR_CL_DDR_52_360: 0x00]
Power class for 52MHz, DDR at 1.95V [PWR_CL_DDR_52_195: 0x00]
Power class for 200MHz at 3.6V [PWR_CL_200_360: 0x00]
Power class for 200MHz, at 1.95V [PWR_CL_200_195: 0x00]
Minimum Performance for 8bit at 52MHz in DDR mode:
[MIN_PERF_DDR_W_8_52: 0x00]
[MIN_PERF_DDR_R_8_52: 0x00]
TRIM Multiplier [TRIM_MULT: 0x02]
Secure Feature support [SEC_FEATURE_SUPPORT: 0x55]
Boot Information [BOOT_INFO: 0x07]
Device supports alternative boot method
Device supports dual data rate during boot
Device supports high speed timing during boot
Boot partition size [BOOT_SIZE_MULTI: 0x20]
Access size [ACC_SIZE: 0x07]
High-capacity erase unit size [HC_ERASE_GRP_SIZE: 0x01]
High-capacity erase timeout [ERASE_TIMEOUT_MULT: 0x01]
Reliable write sector count [REL_WR_SEC_C: 0x01]
High-capacity W protect group size [HC_WP_GRP_SIZE: 0x10]
Sleep current (VCC) [S_C_VCC: 0x07]
Sleep current (VCCQ) [S_C_VCCQ: 0x07]
Sleep/awake timeout [S_A_TIMEOUT: 0x11]
Sector Count [SEC_COUNT: 0x00e90000]
Minimum Write Performance for 8bit:
[MIN_PERF_W_8_52: 0x00]
[MIN_PERF_R_8_52: 0x00]
[MIN_PERF_W_8_26_4_52: 0x00]
[MIN_PERF_R_8_26_4_52: 0x00]
Minimum Write Performance for 4bit:
[MIN_PERF_W_4_26: 0x00]
[MIN_PERF_R_4_26: 0x00]
Power classes registers:
[PWR_CL_26_360: 0x00]
[PWR_CL_52_360: 0x00]
[PWR_CL_26_195: 0x00]
[PWR_CL_52_195: 0x00]
Partition switching timing [PARTITION_SWITCH_TIME: 0x01]
Out-of-interrupt busy timing [OUT_OF_INTERRUPT_TIME: 0x05]
I/O Driver Strength [DRIVER_STRENGTH: 0x3f]
Card Type [CARD_TYPE: 0x57]
CSD structure version [CSD_STRUCTURE: 0x02]
Command set [CMD_SET: 0x00]
Command set revision [CMD_SET_REV: 0x00]
Power class [POWER_CLASS: 0x00]
High-speed interface timing [HS_TIMING: 0x00]
Erased memory content [ERASED_MEM_CONT: 0x00]
Boot configuration bytes [PARTITION_CONFIG: 0x00]
Not boot enabled
No access to boot partition
Boot config protection [BOOT_CONFIG_PROT: 0x00]
Boot bus Conditions [BOOT_BUS_CONDITIONS: 0x00]
High-density erase group definition [ERASE_GROUP_DEF: 0x00]
Boot write protection status registers [BOOT_WP_STATUS]: 0x00
Boot Area Write protection [BOOT_WP]: 0x00
Power ReadOnly locking: possible
Permanent ReadOnly locking: possible
Read Only lock status: not locked
User area write protection register [USER_WP]: 0x10
FW configuration [FW_CONFIG]: 0x00
RPMB Size [RPMB_SIZE_MULT]: 0x04
Write reliability setting register [WR_REL_SET]: 0x1f
Write reliability parameter register [WR_REL_PARAM]: 0x04
Enable background operations handshake [BKOPS_EN]: 0x00
H/W reset function [RST_N_FUNCTION]: 0x00
HPI management [HPI_MGMT]: 0x00
Partitioning Support [PARTITIONING_SUPPORT]: 0x07
Device support partitioning feature
Device can have enhanced tech.
Max Enhanced Area Size [MAX_ENH_SIZE_MULT]: 0x0001d2
Partitions attribute [PARTITIONS_ATTRIBUTE]: 0x00
Partitioning Setting [PARTITION_SETTING_COMPLETED]: 0x00
General Purpose Partition Size [GP_SIZE_MULT_4]: 0x000000
[GP_SIZE_MULT_3]: 0x000000
[GP_SIZE_MULT_2]: 0x000000
[GP_SIZE_MULT_1]: 0x000000
Enhanced User Data Area Size [ENH_SIZE_MULT]: 0x000000
Enhanced User Data Start Address [ENH_START_ADDR]: 0x000000
Bad Block Management mode [SEC_BAD_BLK_MGMNT]: 0x00
Periodic Wake-up [PERIODIC_WAKEUP]: 0x00
Program CID/CSD in DDR mode support [PROGRAM_CID_CSD_DDR_SUPPORT]: 0x01
Native sector size [NATIVE_SECTOR_SIZE]: 0x00
Sector size emulation [USE_NATIVE_SECTOR]: 0x00
Sector size [DATA_SECTOR_SIZE]: 0x00
1st initialization after disabling sector size emulation [INI_TIMEOUT_EMU]: 0x00
Class 6 commands control [CLASS_6_CTRL]: 0x00
Number of addressed group to be released[DYNCAP_NEEDED]: 0x00
Exception events control [EXCEPTION_EVENTS_CTRL]: 0x0000
Exception events status [EXCEPTION_EVENTS_STATUS]: 0x0000
Extended Partitions Attribute [EXT_PARTITIONS_ATTRIBUTE]: 0x0000
Packed command status [PACKED_COMMAND_STATUS]: 0x00
Packed command failure index [PACKED_FAILURE_INDEX]: 0x00
Power Off Notification [POWER_OFF_NOTIFICATION]: 0x00
Control to turn the Cache ON/OFF [CACHE_CTRL]: 0x00
------------Done parsing------------
Writing...
Done.
Z3X EasyJtag Software ver. 2.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1876 mV
CMD Active Level:1876 mV
Input file : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM1_000000000000_000010000000.bin
Writing 0010000000 bytes to 0000000000... ROM1 (USER ROM)
Done. Write Speed: 915 kB/s
Z3X EasyJtag Software ver. 2.5.1.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:1876 mV
CMD Active Level:1876 mV
Input file : D:\أ‡أ،أˆأ¦أںأ“أ‡أٹ\EasyJtag\G530h\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\SAMSUNG_SM-G530H_emmc_direct_dump_264MB\EMMC_QNW00M_ROM2_000000000000_000000400000.bin
Writing 0000400000 bytes to 0000000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 1311 kB/s
المفضلات