أخيرا وبعد مئات المحاولات حل مشكلة البوت j100h و j200h وأى SPD (أرجو التثبيت)

[NEZAR@GSM]

شكرا لتعاونك أخي الكريم
بإجراء الخطوة الأولى : Test Write
وجدت أخطاء كما في اللوغ التالي :

Setting frequence to 14 Mhz
CMD Pullup Level: 1742 mV
CMD Active Level: 2392 mV
EMMC Device Information :
EMMC CID: 90014A4834473262110100B0A8EF52B6
EMMC CSD: D07F01320F5903FFFFFFFFEF8A4040DA
EMMC Manufacture : SKHYNIX , EMMC NAME: H4G2b , HEX: 483447326200 , S/N: 00B0A8EF , rev. 0x01
EMMC Manufacture ID: 0x90 , OEM ID: 0x4A , Device Type: BGA (Discrete embedded) , Date: 5/2015
EMMC ROM 1 (Main User Data) Capacity: 3728 MB (0000E9000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 4096 KB (000000400000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 4096 KB (000000400000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.6 (MMC 4.5, MMC 4.51)
Boot configuration [PARTITION_CONFIG]: 0x08 , Boot from: ROM2 (Boot partition 1)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x07
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Device can have extended partitions attribute
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: H4G2b_00B0A8EF_20180509_115701.extcsd
EMMC Init completed.

Operation: Changing GP sizes (test mode) ...

GP1 size: 0 MB , WR_REL: 1 , ENH 0
GP2 size: 0 MB , WR_REL: 1 , ENH 0
GP3 size: 0 MB , WR_REL: 1 , ENH 0
GP4 size: 0 MB , WR_REL: 1 , ENH 0

HW_PART error. Reason: Zero sizes

تابع الخطوات واذا لم يعمل الهاتف يجب تغيير EMCP

[mandolen]

Setting frequence to 21 Mhz
CMD Pullup Level: 2000 mV
CMD Active Level: 2454 mV
EMMC Device Information :
EMMC CID: 65646F4D204D4F5212A100000240012E
EMMC CSD: D07FFF320F59007FF6DB80001E40001C
EMMC Manufacture : , EMMC NAME: MMOR , HEX: 4D004D4F5200 , S/N: 00000240 , rev. 0xA1
EMMC Manufacture ID: 0x65 , OEM ID: 0x6F , Device Type: Device (removable) , Date: 0/2014
EMMC ROM 1 (Main User Data) Capacity: 128 MB (000008000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x78 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: MMOR_00000240_20190117_191132.extcsd
EMMC Init completed.

eMMC are unusable

[mandolen]

ايه المشكله هنا

Setting frequence to 21 Mhz
CMD Pullup Level: 2000 mV
CMD Active Level: 2454 mV
EMMC Device Information :
EMMC CID: 65646F4D204D4F5212A100000240012E
EMMC CSD: D07FFF320F59007FF6DB80001E40001C
EMMC Manufacture : , EMMC NAME: MMOR , HEX: 4D004D4F5200 , S/N: 00000240 , rev. 0xA1
EMMC Manufacture ID: 0x65 , OEM ID: 0x6F , Device Type: Device (removable) , Date: 0/2014
EMMC ROM 1 (Main User Data) Capacity: 128 MB (000008000000)
EMMC ROM 2/3 (Boot Partition 1/2) Capacity: 2048 KB (000000200000)
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 KB (000000020000)
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD Information :
Extended CSD rev: 1.5 (MMC 4.41)
Boot configuration [PARTITION_CONFIG]: 0x78 , Boot from: ROM1 (Main User Area)
Boot Bus Config: 0x00 , width 1bit
H/W Reset Function [RST_N_FUNCTION]: 0x00, RST_n signal is temporarily disabled
Supported partition features [PARTITIONING_SUPPORT]: 0x03
Device supports partitioning features
Device can have enhanced technological features in partitions and user data area
Partition Settings [PARTITION_SETTING_COMPLETED]: 0x00
Backup saved: MMOR_00000240_20190117_191132.extcsd
EMMC Init completed.

eMMC are unusable

[ahmedshafik2]

مرة أخرى أسأل
صاحب الموضوع
و المشرفين

من أين أحصل على الملف

j100H_UD_1GB_0x00000000_0x001FFFFF.bin

اللي هو أساس الموضوع

و اللي غير موجود في السبورت

آآآآآآآآآآسف جدا على الرد المتأخر جدا بس حضرتك مش محتاج ملف bin أصلا

[Sh.Hasan]

آآآآآآآآآآسف جدا على الرد المتأخر جدا بس حضرتك مش محتاج ملف bin أصلا

لكن هو موجود في الشرح