كل عام وأنتم بخير جميع الأعضاء
سنطرح في موضوعنا هذا اليوم
طريقة إصلاح أجهزة LG Android الميتة أو الفاصلة نهائياً
Unbrick LG G4 Brick hs-usb Qdloader 9008
الموديلات المدعومة:
H815
H818
H818N
H818P
H819
LS995
LS991
H811
رابط تحميل الملفات : Download
تابع الشرح :
وقد خصصنا الشرح باللغة الإنجليزية مدعوماً باللغة العربية حتى يتمكن الأصدقاء الأجانب من إصلاح أجهزتهم
1. Download
QPST.WIN.2.7-00430-GENERAL
Run setup.exe
شغل برنامج ال Setup.exe
بعد التثبيت يمكنك فتح البرنامج من خلال:
Windows [Start] button >> Allprograms >> QPST >> QFIL
installation confirmation
2. Download
Qdload9008_HSUSB_Driver
Install Drivers
قم بتثبيت التعريفات في الرابط أعلاه
3. D / L via QFIL
وهذا هو البرنامج المستخدم في عملية التفليش وأعتقد أن الكل يعرفه
To force QDloader download mode, connect the FORCED_USB emmc section with a jumper.
Or pressing key combination (volup + voldown) and poweron to boot Emergency D / L mode
بعض الهواتف تحتاج إلى كابل EDL وهو متوفر في الأسواق أو يمكنك صنعه بنفسك
After two points in the red circle are shorted and connected by power or USB connection, Qdloadmode can be entered and connected to QFIL
فقط قم بتوصيل التيست بوينت كما بالصورة حتى يكتمل تعريف الهاتف بالكمبيوتر ، وستلاحظ أن الهاتف تم تعريفه على البرنامج
In Emergency D / L mode, check the port in Device Manager after connecting USB -> QS
سوف تلاحظ أن الهاتف قد تعرف من خلال قائمة Device Manager
Windows [Start] button >> All programs >> QPST >> Run QFIL
قم بتشغيل البرنامج المستخدم
تابع عملية الشرح على البرنامج كما بالصور أدناه
Select Port
1. Click the "Select Port" button
If you deselect Show Non Diagnostic Port, only the "Diagnostic" or "QDLoader" port will be visible
Selecting the port identified by Device Manager
MBN file selection
2. Click the "Browse" button
Select the file "prog_emmc_firehose_8992_lite_stable.mbn" in the folder where the images are stored.
For fusing samples, use images made for fusing.
ForFusingDevice: For Fusing Devices -> Download to LAF after recovery
NotForFusingDevice: for non-fused devices -> Restore and download
Select Build, RawProgram, Patch Check
Check RawProgram and Patch settings
Check the rawprogram0.xmlpatch0.xml file included
in the -Select Build path.
firehoseprogrammer MBN selected in the same folder
Rawprogram0.xml, patch0.xml are loaded.
SWDownload
4. Click the "Download" button
- The progress bar below is completed and the Download Succeed -> Finish Download message is confirmed.
في النهاية نشكر الزميل والصديق
Mohammed Alshikh
لعرضه تجاربه المصورة لذلك
تحياتي إليكم دمتم بخير
محمود الشوربجي
المفضلات