فلاشة samsung gt i9190 mtk 6572
الانفو على NCK
META INFO
Start sync target, waiting responce.....
Brand: samsung
Board: e103_lca
Model: GT-I9190
Name: serrano3g
Release: ALPS.JB3.MP.V1
Version: 4.2.2
Mediatek Version: ALPS.JB3.MP.V1
Branch: ALPS.JB3.MP
Platform: MT6572
Modem Version: WR8.W1315.MD.WG.MP CENON72_ET_JB3_xDEFAULT
Reading imei
IMEI[1]: 359883006314781
IMEI[2]: fffffffffffffff
All done.
BOOT INFO
كود:
NAND: (4Gb+2048Mb) [Micron] NAND_MT29C4G48MAAHBAAKS_5WT
BOOT STYLE : NAND BOOT
Size: 0x20000000 [0.500 GB]
BlockSize: 4096 SpareSize: 224 BMT Blocks 80
Preloader SEC version: 2
Status: USB_HIGH_SPEED
Detecting high speed port, wait......
If driver not installed, install high speed port driver.
If not need high speed port, disable it.
After repeat opperation.
Detecting high speed port, wait......
Detected : DA USB VCOM Port (COM10)
Searching partiton table, wait..
[0]Part: PRELOADER Begin: 0x0 Len: 0x100000
[1]Part: PRO_INFO Begin: 0x100000 Len: 0x100000
[2]Part: NVRAM Begin: 0x200000 Len: 0x300000
[3]Part: PROTECT_F Begin: 0x500000 Len: 0x300000
[4]Part: PROTECT_S Begin: 0x800000 Len: 0x300000
[5]Part: SECCFG Begin: 0xb00000 Len: 0x40000
[6]Part: UBOOT Begin: 0xb40000 Len: 0x80000
[7]Part: BOOTIMG Begin: 0xbc0000 Len: 0x600000
[8]Part: RECOVERY Begin: 0x11c0000 Len: 0x600000
[9]Part: SEC_RO Begin: 0x17c0000 Len: 0x40000
[10]Part: MISC Begin: 0x1800000 Len: 0xc0000
[11]Part: LOGO Begin: 0x18c0000 Len: 0x100000
[12]Part: EXPDB Begin: 0x19c0000 Len: 0x200000
[13]Part: FAT Begin: 0x1bc0000 Len: 0x1400000
[14]Part: ANDROID Begin: 0x2fc0000 Len: 0xf000000
[15]Part: CACHE Begin: 0x11fc0000 Len: 0x700000
[16]Part: USRDATA Begin: 0x126c0000 Len: 0xcec0000
[17]Part: BMTPOOL Begin: 0xffff0028 Len: 0x0
Offset: 0x1f400000 Count: 18
IMEI[1]: 359883006314781
IMEI[2]: 359883006314781
Wait untill phone will start charging.
All done.
انا اخذت الانفو على NCK لان الجهاز لا يكمل الانفو على الميراكل
الانفو على الانفينتي
كود:
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 4 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8B00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x00FF
BLVersion : 0x0001
PreLoader : Active [ Boot with PL ]
BootLdrSS : NORMAL with PRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : 002C00BC009000660054000000000000
eMMC Flash : NOT INSTALLED
Initialize Memory ...
DRAM already initialized by Preloader
DAgent sent , init HW now
NAND FlashIC initialized
[NAND] : FLASH_VEN : 0x0092 , [Micron] NAND_MT29C8G96MAZBADKD_5WT
[NAND] : FLASH_DIE : 002C 00BC 0090 0066 0054 0000 0000
[NAND] : FLASH_LEN : 0x20000000
[NAND] : FLASH_EXT : 1000/0040/01/NIM_Px-1
DEV RID : 0xC3B490A9DBFCD0159F1F622FB1026FB1
INT RAM : 0x00020000
EXT RAM : 0x10000000 [256 MiB]
BOOT TYPE : NAND_FLASH_BOOT
SOC VERIFY : C1
Boot Ok!
[AP] : Initial info read Ok!
Brand : samsung
ProdName : serrano3g
ProdModel : GT-I9190
Device : serrano3g
AndroidVer: 4.2.2
MTKxCPU : MT6572
MTKxPRJ : ALPS.JB3.MP.V1
SECURITY :
IMEI_SW [1] : 359883006314781
BTMAC Addr : 000046657201
WiFi MAC : 000000000000
Done!
Elapsed: 00:00:41
Reconnect Power/Cable
الانفو على الميراكل ما بيكمل
Definition Applied
Waiting for USB Port...
Set PreLoader USB VCOM Port (COM4)
Please Hold "ON" to connect with the phone...
Connected to Phone.
CPU: MT6572 SW:0000 Ver: CA01
Downloading Boot8 ...
Nand Flash Type: Nand_NEW_006E
Nand Flash Code: 002C00BC(00900066)
Nand Flash Size: 0x20000000 Hex Bytes
INT/EXT RAM Size: 0xC4800+0x0
>>ERROR
اسم الفلاشة على CM2
MT6572_NAND_samsung__GT-I9190__serrano3g__4.2.2__ALPS.JB3.MP.V1
رابط التحميل
MT6572_NAND_samsung__GT-I9190__serrano3g__4.2.2__ALPS.JB3.MP.V1 - Download - 4shared
باسوورد فك الضغط
المفضلات