السلام علسكم
من فضلكم اخواني عند تفليش هاتف condor c4
سفشل الدانقل من إكمال التفليش وهذا هو الانفو
كود PHP:
Operation : Check / Read Info [ v1.54 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 38 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004E35585A4D4201FABFCE3371C9
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x00 , OEM : 0000
[eMMC] : FLASH_INF : [NOT_IN_BASE] ,
[eMMC] : FLASH_CID : 00000000000000000000000000000000
[eMMC] : FLASH_BRT : 0x00000000 , 0x00000000 , 0x00000000
[eMMC] : FLASH_LEN : 0x0000000000000000
[eMMC] : FLASH_UCP : 0 MiB [eMMC BAD_CONN]
DEV RID : 0xAE7BF7BFEE60EEB5D68D84665C653582
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : DA_HANDSET_ROM_INFO_NOT_FOUND
SOC VERIFY : C1
Boot Ok!
Info read not done :( Erased phone or unsupported FlashIc?
You can change settings : Settings -> Other -> NAND init Mode
Done!
Elapsed: 00:00:19
Reconnect Power/Cable!
وهذا انفو الفلاش
فارجو الحل من الخبراءكود PHP:
Card found : S/N : D62DC3AD , v0132
Chinese Miracle II [MTK module] v 1.54
Scatter Load Ok , BaseBand : MT6572 , Project : Condor_PGN-403_jb3 , Storage : EMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!
Operation : Flash [ v1.54 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 38 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004E35585A4D4201FABFCE3371C9
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x00 , OEM : 0000
[eMMC] : FLASH_INF : [NOT_IN_BASE] ,
[eMMC] : FLASH_CID : 00000000000000000000000000000000
[eMMC] : FLASH_BRT : 0x00000000 , 0x00000000 , 0x00000000
[eMMC] : FLASH_LEN : 0x0000000000000000
[eMMC] : FLASH_UCP : 0 MiB [eMMC BAD_CONN]
DEV RID : 0xAE7BF7BFEE60EEB5D68D84665C653582
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : DA_HANDSET_ROM_INFO_NOT_FOUND
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6572 , Project : Condor_PGN-403_jb3 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
Switching to HSUSB
HSUSB Init Ok
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC NOT supported by BootLoader!
[BL_ERROR] : STORAGE : Break Flashing! This Firmware will kill phone!
Operation Failed
Elapsed: 00:00:22
Reconnect Power/Cable!
المفضلات