انا الان فكيته وشبكت الوصلة عليه مباشر عشان اعطيه الفلاش واعطاني التالي :
JAF version 1.98.60
Detected PKEY: 9001AE0F
Card life counter: 58.03%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B0, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.0.2.0
Backup IMEI zone...
Setting local mode...
Failed! Aborting!
Getting MCUID...
Phone didn't answer with TX line high after power on!
Causes:
1. Phone don't power on -> Check cable
2. TX pin from phone don't make contact -> Check cable
3. UPP damaged -> change UPP
MCU ID: 0xAAAA
Failed!!!
Backup IMEI zone...
Setting local mode...
Failed! Aborting!
Getting MCUID...
Phone didn't answer with TX line high after power on!
Causes:
1. Phone don't power on -> Check cable
2. TX pin from phone don't make contact -> Check cable
3. UPP damaged -> change UPP
MCU ID: 0xAAAA
Failed!!!
Backup IMEI zone...
Setting local mode...
Failed! Aborting!
Getting MCUID...
Failed!!!
Backup IMEI zone...
Setting local mode...
Failed! Aborting!
Getting MCUID...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
Failed!!!
Backup IMEI zone...
Setting local mode...
Failed! Aborting!
Getting MCUID...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
Failed!!!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.060
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.060
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.06ic
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.060
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.06ic
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm3050_nai5.06ic
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
MCU: C:\Program Files\Nokia\Phoenix\Products\RM-305\rm305_05.060
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
يعني مازبطش
رد مع اقتباس.gif)
المشاركة الأصلية كتبت بواسطة tarek weshah
المفضلات