n7100 repair emmc with easy jtag بنجاح

[m-mulham]

تم بعون الله ربيير emmc n7100 بنجاح على العملاق
الهاتف كان يقف على الشعار و عند محاولة الدخول على الريكفري ترجف الشاشة ويفصل الهاتف

يدخل داونلود مود ياخد سوفت ولكن يبقى على الشعار
استعنت بالفيدبو ده كما اشار علي الريس حسام في موضوع سابق
Repair EMMC damaged No Product Name Z3x Easy Jtag I9300 - YouTube
لكن الهاتف يعمل فورمات ولا برضى تمرير ملف الدامب
جربت طريقة الكبير

LYON في الموضوع ده
شرح حصرى لطريقة تصليح Emmc I9060 على EasyJtag
ايضا يمسح ولا يرضى تمرير ملف الدامب
وانا بدور شفت الفيديو ده
n7100 boot repair via direct emmc with easy jtag ihab djafi - YouTube
نفذته خطوة خطوة نجحت العملية واشتغل الهاتف وفلشتو بملف واحد وعاد للحياة
كل الشكر لمشرفي القسم الذين لم يبخلوا علينا بالاجابة اترككم مع لوغ العملية
EasyJtag Suite ver.: 2.0.6.8 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).
EasyJtag API ver.: 1.0.9.0
Android Explorer ver.: 1.1.0.9
eMMC ODIN ver.: 1.0.11.1
Successfully connected to box on COM3
Box S/N: 0900D022A4E5A705, ,FW Ver.: 01.52
Box Working Mode: JTAG Box.
Box Drivers version: 3.0.0.0, are OK
Z3X Card Serial : AA89-F4A4 , ver: 22
Z3X Card Activation [LG] : ACTIVATED
Z3X Card Activation [SAMS] : ACTIVATED, Upgrade it!
Z3X Card Activation [JTAG] : ACTIVATED
Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 0900D022A4E5A705, ,FW Ver.: 01.52
CMD Pullup Level:752 mV
CMD Active Level:1732 mV
eMMC Device Information
EMMC CID : 15010056545530304DF780E04B54CFBC
EMMC CSD : D02701320F5903FFF6DBFFFF8E406008
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 12/2012 Rev.0xF7
EMMC NAME: VTU00M , S/N: 2162182996
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: Yes
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x48] Boot from:ROM2 (Boot Partition 1)
Boot bus config [177]: 0x01 , width 4bits , Partition config [179]: 0x48.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: VTU00M_2162182996_20160226_1923.extcsd
Done.


Checking NAND Image : C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
File successefuly loaded!
Processing file...C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1732 mV
Input file : C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.


Processing file...C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
ROM2 Are not selected , skip writing ROM2
ROM3 Are not selected , skip writing ROM3
extCSD Are not selected , skip writing extCSD
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1732 mV
Input file : C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 ...ROM1 (USER ROM)
Write Block Failed, Reason: Write Block Verify Error
Done.


Running:SAMSUNG: MoviNAND Reset + Format...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1732 mV
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Sending Internal Reconfiguration Request...
Waiting configuration Apply!
Restoring configuration...
EMMC ROM2/3 (Boot Partitions) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
Wiping Card... Please do not touch it!
Please don't forget to repair extCSD from backup!
Done.


Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:752 mV
CMD Active Level:1732 mV
Repair VTU00M eMMC:
Entering repair mode 2...
Success!
Erasing repair area...
Success!
Writing repair area...
Success
Exit repair mode 2...
Success
EMMC repair Done , Reconect eMMC and check S.M.A.R.T Report.
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!


Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 0900D022A4E5A705, ,FW Ver.: 01.52
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
eMMC Device Information
EMMC CID : 1501003030303030300C201301281062
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 01/2013 Rev.0xC
EMMC NAME: 000000 , S/N: 538116392
EMMC NAME (HEX): 30303030303000
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: 000000_ 538116392_20160226_1934.extcsd
Done.


Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success!
Erasing repair area...
Success!
Writing repair area...
Success!
Exit repair mode 1...
Success
NOTE: This stage was reapir only eMMC NAME , not wear leveling data!
NOTE: Repair Stage 2 must be done to make eMMC repair completely!
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
Done.


Running:SAMSUNG: MoviNAND VTU00M Name 0000 Repair...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Repair VTU00M eMMC:
Entering repair mode 1...
Success!
Erasing repair area...
Success!
Writing repair area...
Success!
Exit repair mode 1...
Success
NOTE: This stage was reapir only eMMC NAME , not wear leveling data!
NOTE: Repair Stage 2 must be done to make eMMC repair completely!
Please, Reconnect eMMC power lines and press 'VTU00M Repair' again
Done.


Running:SAMSUNG: eMMC firmware update...
Confirmed eMMC Part Number: kmvtu000lm-b503
Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 0900D022A4E5A705, ,FW Ver.: 01.52
Warning: CMD Pullup Level (804 mV) too low , check cables etc.!
CMD Active Level:2423 mV
Setup firmware update mode, wait 2..30 sec...
Success!
Sending eMMC firmware...
Success!
Verifying eMMC firmware...
Success!
Flashing eMMC firmware...
Success!
Repairing eMMC CID...
Success!
eMMC firmware is updated now!
Please reconnect all eMMC lines before next operation!
Please don't forget to repair extCSD from backup!
Please don't forget to configure BOOT sizes!
Done.


Z3X EasyJtag Software ver. 2.0.6.8
Loading eMMC Addon Firmware... IO: 3300 mV
Box S/N: 0900D022A4E5A705, ,FW Ver.: 01.52
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
eMMC Device Information
EMMC CID : 15010056545530304DFC3D39868641FA
EMMC CSD : D02701320F5903FFF6DBFFFF8E40406C
EMMC Manufacturer ID: 0015 , OEM ID: 0100
EMMC Date: 04/2014 Rev.0xFC
EMMC NAME: VTU00M , S/N: 1027180166
EMMC NAME (HEX): 56545530304D00
EMMC ROM1 (Main User Data) Capacity: 15028 MB
EMMC ROM2 (Boot Partition 1) Capacity: 2048 kB
EMMC ROM3 (Boot Partition 2) Capacity: 2048 kB
EMMC RPMB (Replay Protected Memory Block) Capacity: 128 kB
EMMC Permanent Write Protection: No
EMMC Temporary Write Protection: No
Extended CSD rev 1.6 (MMC 4.5)
Boot configuration [PARTITION_CONFIG: 0x00] No boot partition configured.
Boot bus config [177]: 0x00 , width 1bit , Partition config [179]: 0x00.
H/W reset function [RST_N_FUNCTION]: 0x00
Backup saved: VTU00M_1027180166_20160226_1944.extcsd
Done.


Checking NAND Image : C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
File successefuly loaded!
Processing file...C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Input file : C:\Users\mulham\Desktop\N7100\EMMC_00000000_00200000.bin
Writing 0000200000 bytes to 00000000 ...ROM2 (BOOT1 ROM)
Done. Write Speed: 819 kB/s


Checking NAND Image : C:\Users\mulham\Desktop\N7100\N7100_Rom1_Alive_Dump_BN.bin
File successefuly loaded!
Processing file...C:\Users\mulham\Desktop\N7100\N7100_Rom1_Alive_Dump_BN.bin
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Input file : C:\Users\mulham\Desktop\N7100\N7100_Rom1_Alive_Dump_BN.bin
Writing 0020000000 bytes to 00000000 ...ROM1 (USER ROM)
Done. Write Speed: 2885 kB/s


Running:Change BOOT CONFIG...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Writing eMMC Register...
Written: REG : 179 VAL :48
Done.


Running:Change BOOT WIDTH...
Z3X EasyJtag Software ver. 2.0.6.8
Skip loading eMMC Addon Firmware
CMD Pullup Level:814 mV
CMD Active Level:2423 mV
Writing eMMC Register...
Written: REG : 177 VAL :1
Done.

[m-mulham]

اسف لعدم تنسيق الموضوع

[SaiD_KHeirallaH]

شكرا لعرض التجربه الناجحه

[HaMdY_gsm]

شكرا ع عرض التجربة

[rabiegsm]

شكرا لعرض التجربه

[ezak]

شكرا لعرض تجربتك الناجحه

[LYON]

الله ينور عليك يا بوووب
وشكرا لك لارفاق الفيديو
بالتوفيق

[..::Mr.TpO::..]

مبروك عليك الجهاز يابوب ومشكور على التركة

[tarek250]

شكرا لعرض التجربة
وارفاق الفديو

[EXplORer_70]

شكرا لك حبيبيى على العرض