بوت n7000 جنني

[eslamgad]

Connecting to the dead body...OK
Detected dead body ID: 0x4BA00477 - CORRECT!
Set I/O Voltage reads as 2.82V, TCK Frequency is 8 MHz


Resurrection sequence started.
Establish communication with the phone...OK
Initializing internal hardware configuration...OK
Uploading resurrector data into memory...OK
Starting communication with resurrector...OK


WARNING: DCC Loader was unable to initialize FLASH1 chip. Error code: 0x00000048


No Resurrection Data is available for the eMMC Chip with Capacity = 0B
WARNING!!! Using Resurrection Data for the eMMC Chip with Capacity = 14.68GB


ERROR: Selected FLASH Chip was not initialized by the DCC Loader.
كده الجهاز فيه مشكله في emmc صح ولا خطا

[eslamgad]

ودي قرايت الايزي كمان
EasyJtag Suite ver.: 1.6.3.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).


For support and updates visit EasyJtag – most powerfull eMMC and JTAG tool on market. | EMMC BOX, JTAG BOX ,Z3X , BOOT REPAIR , FORENSICS TOOL
Check security...OK
Initialising: SAMSUNG GT-N7000 Config ver.:1.00
I/O Level set to : 2800 mV
Box S/N: 0DFFA01A5BAD6AFA ,FW Ver.: 01.50
Connecting to Target...
JTAG device: S5PC210
CPU IDCODE : 0x4BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x4
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A9
Halting CPU...
Init target ...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC Not Initialised!
BUG: emmc unknown controller initialization failure


Z3X EasyJtag Software ver. 1.6.3.0
Loading eMMC Addon Firmware... IO: 1850 mV
Box S/N: 0DFFA01A5BAD6AFA, ,FW Ver.: 01.50
CMD Pullup Level:2763 mV
CMD Active Level:2835 mV
Can't init EMMC, Reason: CMD Timeout Error
===================================
Done.
Erasing Blocks...


Z3X EasyJtag Software ver. 1.6.3.0
Skip loading eMMC Addon Firmware
CMD Pullup Level:2763 mV
CMD Active Level:2835 mV
Can't init EMMC, Reason: CMD Timeout Error
===================================
Using EasyRepair Mode...
Checking repair data...
EasyJtag Suite ver.: 1.6.3.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).


For support and updates visit EasyJtag – most powerfull eMMC and JTAG tool on market. | EMMC BOX, JTAG BOX ,Z3X , BOOT REPAIR , FORENSICS TOOL
Check security...OK
Initialising: SAMSUNG GT-N7000 Config ver.:1.01
I/O Level set to : 2800 mV
Box S/N: 0DFFA01A5BAD6AFA ,FW Ver.: 01.50
Connecting to Target...
JTAG device: S5PC210
CPU IDCODE : 0x4BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x4
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A9
Halting CPU...
Init target ...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC Not Initialised!
BUG: emmc unknown controller initialization failure
Using EasyRepair Mode...
Checking repair data...
EasyJtag Suite ver.: 1.6.3.0 / wxWidgets 3.1.0-W-U started.
Operating system ver.: Windows 7 (build 7601, Service Pack 1).


For support and updates visit EasyJtag – most powerfull eMMC and JTAG tool on market. | EMMC BOX, JTAG BOX ,Z3X , BOOT REPAIR , FORENSICS TOOL
Check security...OK
Initialising: SAMSUNG GT-N7000 Config ver.:1.01
I/O Level set to : 2800 mV
Box S/N: 0DFFA01A5BAD6AFA ,FW Ver.: 01.50
Connecting to Target...
JTAG device: S5PC210
CPU IDCODE : 0x4BA00477 Mfg.: 0x23b, Part: 0xba00, Ver.: 0x4
CPU Manufacturer: QUALCOMM , CPU Name: CORTEX A9
Halting CPU...
Init target ...
Starting target communication...
Detecting emmc memory parameters of bank (0) ...
EMMC Not Initialised!
BUG: emmc unknown controller initialization failure