فلاشه 1112 صينى

[HSH_2020]

جهاذ 1112 عايز سوفت ص
Detected PKEY: 900177CF
Card life counter: 98.02%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B0, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.0.2.0
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.910
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.910
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.91ic
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.910
PPM Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.91ic
CNT Flash file: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh930_nai6.91ic
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
MCU: C:\Program Files\Nokia\Phoenix\Products\RH-93\rh93_06.910
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
ناعه صينى نزلت فلاشه عاديه ياتى العباره دى

[أبو ملك]

جهاذ 1112 عايز سوفت ص
mcu: C:\program files\nokia\phoenix\products\rh-93\rh93_06.910
booting phone...
Phone didn't answer with tx line high after uem reset!
Causes:
1. Bsi line is not connected properly in connector -> check cable, also for 3.3k resistor in serial with bsi line.
2.uem damaged -> replace uem.
Mcu id: 0xcccc
this mcu id is not supported in chosen flash file...
error booting phone...
ناعه صينى نزلت فلاشه عاديه ياتى العباره دى

غير صالح في اختيار ملف الفلاش

[تيتو المتخصص]

اختيار الفلاشه المناسبه

[°•.WaNTeD.•°]

طبيعي الفلاشة غير مناسبة عشان الانواع الصيني 1112 مش بتقبل السوفت العادي وانا مجرب كدة