نوكيا 107

[محمدلطيف]

الجهاز يومض ، بمعنى انه يقلع نوكيا ثم اعادة اقلاع فى ثوانى على نوكيا ايضا وهكذا ،
لوج انفو وفلاش

Phone found!
Series 40 Device detected!
read info... - Ok

Reading Product code...
Product code : 059T2B8
Done!

Write Product code to phone...
Write done... Check now...
Product code : 059T2B9
Code changed Ok!

Reading Phone Info....
SW ver : V 02.70 08-08-13 RM-961 (c) Nokia
IMEI : 359993057785324
PPM : V 02.70
08-08-13
RM-961
(c) Nokia
IA
PCode : 059T2B9
BPCode : 059S7H5
HWID : 2000
LCDVer : TINAMA:BARACOAv8A
NT39121
IMEI : 359993057785324
Sl Conf : 001-01-00000000000
Sl Prof : 000000000004000-2
Sl Aux : 000B0000
Hw Sig : 85983223EAF6D762
Country : Test SIM (Open)
Operator : NOKIA (Open)

Lock info:
Block 1
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 2
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 3
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 4
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 5
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 6
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;
Block 7
L1:Open; L2:Open; L3:Open; L4:Open; L5:Open;

Done!

Core : v1.51 , FlashEngine : v1.8

Selected FlashSettings :
Files Set for Flashing :
MCU : rm961_02.700
PPM : rm961_02.70ia
CNT : rm961_nai02.70ia

Infineon flashing...
-> Infineon XG110 : IMEI Backup Created
Booting phone now....
Sync Ok , A2
CPU ID : XGOLD , A200341100
PBL : Dynamic
Boot Ok , 01AB
SBL : Dynamic
Algo Ok , 01
SBL mode Ok
SBL : Default_RAM_Bootloader
EPP CFG [Bering]...
FLASH ID : 0020000000048800
FLASH ID : UNKNOW [Not In Base]
Boot Done!

===Flashing [MCU]===
File : rm961_02.700
Image : hw_b1_rm961_02.700.fls
Cert block found, sending....
Cert sent
Found 3 region(s)
Processing Region 1/3
Erase , Start : 0x00000000 , Len : 0x00020000
Erasing, wait ...
Erase done
Write , Start : 0x00000000 , Len : 0x00006000
Flashing , wait ...
Region flash done
Processing Region 2/3
Erase , Start : 0x00800000 , Len : 0x00400000
Erasing, wait ...
Erase done
Write , Start : 0x00800000 , Len : 0x003F0000
Flashing , wait ...
Region flash done
Processing Region 3/3
Erase , Start : 0x00C5D000 , Len : 0x00203000
Erasing, wait ...
Erase done
Write , Start : 0x00C5D000 , Len : 0x0019E700
Flashing , wait ...
Region flash done
Check : FCAF
===Flashing [PPM]===
File : rm961_02.70ia
Image : hw_b1_rm961_02.70ia.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00100000 , Len : 0x00700000
Erasing, wait ...
Erase done
Write , Start : 0x00100000 , Len : 0x00571840
Flashing , wait ...
Region flash done
Check : 9F27
===Flashing [CNT]===
File : rm961_nai02.70ia
Image : hw_b1_rm961_nai02.70ia.fls
Cert block found, sending....
Cert sent
Found 1 region(s)
Processing Region 1/1
Erase , Start : 0x00E60000 , Len : 0x00100000
Erasing, wait ...
Erase done
Write , Start : 0x00E60000 , Len : 0x000FEE00
Flashing , wait ...
Region flash done
Check : A114

Flashing done, rebooting...
-> Infineon info : Do FullFactory Sets after flashing
Flashing Done!


Init Service mode... Wait...

Afterflash settings...
SW ver : V 02.70
08-08-13
RM-961
(c) Nokia
IMEI : 359993057785324
PCode : 059T2B9
Settings After Flash Defaults...
FullFactorySet...OK!
ProductTuneSet...OK!
SwUpgradeSet...OK!
All done!

Connect phone on selected interface...

Connect phone on selected interface...

Phone found!
Series 40 Device detected!
read info... - Ok
مساعدة وجزيتم خيرا

[manse]

قم بتجربة اصدار اخر

[محمدلطيف]

جارى البحث عن اصدار مختلف ، والرد

[محمدلطيف]

فلاش باصدار مختلف ونفس المشكلة قائمة
CPU: XGOLD 110
Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.24
EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 8804 - 23280001 [ST 58LR128U,128 Mbits]
CFI information:
Flash settings: 0/64, size: 0x01000000
2 Block regions:
127 x 0x00020000 = 0x00FE0000
4 x 0x00008000 = 0x00020000
EBL ready !
Processing file: rm961_02.900
Downloading item CODE:hw_b1_rm961_02.900.fls, num block: 3, size: 5.58 MB
Erasing area 0x00000000-0x00005FFE ...OK
Programming completed in 0.593 s
Erasing area 0x00800000-0x00BEFFFE ...OK
Programming completed in 1 min 19.906 s
Erasing area 0x00C5D000-0x00DFB6FE ...OK
Programming completed in 29.797 s
Checksum verified (0x552F)
Processing file: rm961_02.90mg
Downloading item CUST:hw_b1_rm961_02.90mg.fls, num block: 1, size: 5.45 MB
Erasing area 0x00100000-0x0067183E ...OK
Programming completed in 1 min 41.594 s
Checksum verified (0x1E70)
Processing file: rm961_nai02.90mg
Downloading item CODE:hw_b1_rm961_nai02.90mg.fls, num block: 1, size: 1022.77 KB
Erasing area 0x00E60000-0x00F5EDFE ...OK
Programming completed in 19.828 s
Checksum verified (0x5DF2)
Total time for flashing process(boot+erase+write) was 6 min 3.438 s


Phone type: RM-961
SW version: V 02.90 22-10-13 RM-961 (c) Nokia
Imei plain: 35999305778532-4
Product code: 059T2B9
Cellular system: GSM
ASIC ID: 0x2292, type: 11
Ppm Id: MG
Language Pack:
- not available.

Master code: 3203503356

Imei net: 35999305778532
Provider: GSM Test Operator
Counter: 0/3, 0/10

CONFIG_DATA: 0010100000000000
PROFILE_BITS: 0000000000040002

BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN

[s.a.s.a]

تأكد من نضافة الجهاز جيدا بعد محالاوت السوت وير اخى الكريم

[samar_fone]

مشكورررررررررررررررررررررررررررررررررررررررررررررررررررررر