n8 ضارب رقم تسلسلي
قبل تفليش تفقدت رقم تسلسلي وكان سليم ب #06#
وقبل التفليش إحتفظت بrpl ووجدته RM-596_1234561065432109042014_123448.RPL
لوق تفليش
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
Sending User Abort Signal...
Phone not detected at USB -> User Abort
Proceeding with Recovery Mode...
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 03B0010D31D703440AB7A1E489FF35BFFA637EB9
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
APE Subsystem Not Found
NPC Backup stored in "03B0010D31D703440AB7A1E489FF35BFFA637EB9_09042014_123352.NPC.CMT.crt"
[Nokia USB Flashing Generic]: Port opened OK!
Recovery Mode Failed, storing Certificates Only
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
XGold223 ROM Detected
Failed to Boot CMT -> Failed to get First Boot Block
Prepare phone failed with message -> Failed to Boot CMT
Failed to Create RPL from phone -> Failed to Boot / Prepare Phone
RPL backup thread finished, continuing...
Pre flash tasks finished, continuing...
Processing RM-596_014.002_79.92_prd.core.fpsx (CMT)...
Booting CMT...
Sending User Abort Signal...
BB5 USB Boot Rom not Detected -> User Abort
Failed to Boot CMT -> No compatible USB devices detected
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process RM-596_014.002_79.92_prd.core.fpsx
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
[Nokia N8-00 USB Phonet]: Port opened OK!
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-596_12345610654321_09042014_123454.SecurityBlock.PM"
WARNING: "03B0010D31D703440AB7A1E489FF35BFFA637EB9.B00016E6" Not Exists, Will read it...
Reading CYC file from phone...
Booting CMT...
[Nokia N8-00 USB Phonet]: Port opened OK!
Switching to RAW Mode...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 03B0010D31D703440AB7A1E489FF35BFFA637EB9
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
New_RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.10.48.1, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Sending Auxiliary Loader...
Auxiliary Loader Sent!
Loader: RAPxx CommonBoot v1.06 (C) 2011 KarwosLabs
Custom loader running OK! Working...
If phone doesn't powering into Local Mode now for some reason do following:
1. Re-insert battery
2. Power it on, when asked use Ovi/Pc Suite Mode
Readed OK, Saving to "03B0010D31D703440AB7A1E489FF35BFFA637EB9.B00016E6"
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
Storing CMLA Key...
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 03B0010D31D703440AB7A1E489FF35BFFA637EB9
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
APE Subsystem Not Found
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
CMT PARTNERC Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Backing up simlock...
[Nokia USB Flashing Generic]: Port opened OK!
Simlock backup problem -> Phone not detected
Backup simlock thread finished, continuing...
Pre flash tasks finished, continuing...
Processing RM-596_014.002_79.92_prd.core.fpsx (CMT)...
Booting CMT...
[Nokia USB Flashing Generic]: Port opened OK!
XGold223 ROM Detected
Failed to Boot CMT -> Failed to get First Boot Block
Processing Flash Image Failed -> Failed to Boot CMT
Failed to Process all Image files -> Failed to process RM-596_014.002_79.92_prd.core.fpsx
Processing pre flash tasks...
Backing up RPL...
RPL Creation started...
Processing CMT Part...
[Nokia N8-00 USB Phonet]: Port opened OK!
Storing Product Code...
Storing PSN...
Storing HWID...
Trying to store Simlock...
Reading Configuration Key...
Hashing...
Reading SHA1-RSA Signature...
Reading SHA1-HMAC Signature...
Storing Simlock...
Trying to store WMDRM RPL...
Reading Keys...
Storing WMDRM PD...
Reading Security Block...
Security block OK and saved to "RM-596_12345610654321_09042014_123557.SecurityBlock.PM"
"03B0010D31D703440AB7A1E489FF35BFFA637EB9.B00016E6" Exists, That is good...
Storing Additional Data...
Checking Superdongle Key...
Encrypting Superdongle Key...
Storing Superdongle Key...
Checking CMLA Key...
Storing CMLA Key...
Booting CMT...
[Nokia N8-00 USB Phonet]: Port opened OK!
Switching to RAW Mode...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 03B0010D31D703440AB7A1E489FF35BFFA637EB9
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
APE Subsystem Not Found
Storing NPC...
Storing CCC...
Storing HWC...
CMT VARIANT Not Found
CMT PARTNERC Not Found
Restarting MCU...
RPL Saved OK
RPL backup thread finished, continuing...
Backing up simlock...
[Nokia USB Flashing Generic]: Port opened OK!
Simlock backup problem -> Phone not detected
Backup simlock thread finished, continuing...
Pre flash tasks finished, continuing...
Processing RM-596_014.002_79.92_prd.core.fpsx (CMT)...
Booting CMT...
[Nokia N8-00 USB Phonet]: Port opened OK!
Switching to RAW Mode...
[Nokia USB Flashing Generic]: Port opened OK!
Old ROM Detected
CMT_SYSTEM_ASIC_ID: 000000030000022600010007600C192102031104
CMT_EM_ASIC_ID: 00000C35
CMT_EM_ASIC_ID: 00000C30
CMT_PUBLIC_ID: 03B0010D31D703440AB7A1E489FF35BFFA637EB9
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 916F75217F32081248B15C38DFC8E81B
CMT_BOOT_ROM_CRC: E693EF0D
CMT_SECURE_ROM_CRC: AC22615B
CMT Ready!
RM-596_014.002_79.92_prd.core.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
Searching for BootCode: DualLine 32Bit
RAPUv11_2nd.fg, Type: 2nd Boot Loader, Rev: 768.12.14.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Waiting for USB Boot ROM Answer...
ROM Ret: 0xFFFD125D
ROM CMT dwAddr: 0x10004FF0
ROM CMT dwLength: 0x00627837
Seems ROM Initialized OK!
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0000000000000000, Unknown, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x00EC005000000232, Samsung, ONENAND
Requested Algorithm: XSR 1.6 (CMT)
Searching for BootCode: DualLine 32Bit
FlashChip 0x00EC0050 (Samsung), Size: 512MBytes, VPP: Not Supported
RAPUv11_XSR17_alg.fg, Type: Algorithm, Rev: 768.12.14.0, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00040000-0x0007FFFF, ONENAND
EraseArea[0,CMT]: 0x000C0000-0x008BFFFF, ONENAND
EraseArea[0,CMT]: 0x00DC0000-0x0E97FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 0.889s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT ADA Certificate...
Writing CMT KEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT SOS+PMML Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT SOS*UPDAPP Certificate...
Writing CMT SOS*DSP0 Certificate...
Writing CMT LDSP Certificate...
Writing CMT SOS*ISASW Certificate...
Writing CMT SOS+CORE Certificate...
Writing CMT SOS+ROFS1 Certificate...
Programming Status OK!
All blocks written OK! Time taken 25.256s
Flashing Speed: 43635,99 kBit/S
Processing RM-596_014.002_79.92_prd.core.fpsx (APE)...
Processing RM-596_014.002_13.01_MEA_A_79.92_prd.rofs2.fpsx (CMT)...
RM-596_014.002_13.01_MEA_A_79.92_prd.rofs2.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
Started group flash erase
EraseArea[0,CMT]: 0x09F40000-0x0DA7FFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.234s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT SOS+ROFS2 Certificate...
Programming Status OK!
All blocks written OK! Time taken 6.365s
Flashing Speed: 45371,12 kBit/S
Processing RM-596_014.002_13.01_MEA_A_79.92_prd.rofs2.fpsx (APE)...
Processing RM-596_014.002_U08.01_79.92_prd.uda.fpsx (CMT)...
RM-596_014.002_U08.01_79.92_prd.uda.fpsx, Type: Flash Image, Algo: XSR 1.6, BB5
PAPUBKEYS Hash for CMT: D172C32473AE199B213465ABB3853246F9631231
Started group flash erase
EraseArea[0,CMT]: 0x0EA00000-0x1EFFFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.952s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 10.499s
Flashing Speed: 42128,95 kBit/S
Processing RM-596_014.002_U08.01_79.92_prd.uda.fpsx (APE)...
Restarting MCU...
All images processed OK! Processing post flash tasks...
Setting Factory Defaults...
[Nokia USB Flashing Generic]: Port opened OK!
[Nokia USB Flashing Generic]: Port opened OK!
[Nokia N8-00 USB Phonet]: Port opened OK!
[Nokia N8-00 USB Phonet]: Port opened OK!
[Nokia N8-00 USB Phonet]: Port opened OK!
[Nokia N8-00 USB Phonet]: Port opened OK!
[Nokia N8-00 USB Phonet]: Port opened OK!
Factory defaults OK
Reading info...
[Nokia N8-00 USB Phonet]: Port opened OK!
MCU Version V 92PS1_10w46.9
MCU Date 01-03-11
Product RM-596 (Nokia N8)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452311F0000000
PSN MLI345576
Basic Product Code 0596826
PSD 0000000000000000
LPSN 0
APE SW 014.002
APE Variant 014.002.00.01014.002.13.01
APE Test rm596_ENO_2010wk46v141
APE HW 256
APE ADSP 256
APE BT HCI Version 4 (rev. 0). LMP Version 4 (rev. 7455). Manufacturer 13.
RETU 35
TAHVO 00
AHNE 11
HW 7470
RFIC |Alli_4.3.4
DSP TB92PS1_10w46.4
Failed to read info -> Failed to read SP info
Read info thread finished, continuing...
Post flash tasks finished!
Flashing successfully finished!
[Nokia N8-00 USB Phonet]: Port opened OK!
Failed to reset Attempts counter
Failed to Read Security Code -> No any security code found
[Nokia N8-00 USB Phonet]: Port opened OK!
Failed to Read Security Code -> No any security code found
[Nokia N8-00 USB Phonet]: Port opened OK!
Failed to Read Security Code -> No any security code found
Failed to Write RPL File -> No RPL File Provided by User
Failed to Write RPL File -> No RPL
رد مع اقتباس
.gif)
المشاركة الأصلية كتبت بواسطة AMAZIGH
المفضلات