ساعدوني لتحديث البوكس.
السلام عليكم اهل المنتدى و بعد . مشكلتي لم أجد لها حل على الاطلاق و قد بحثت في كل المنتديات لذلك لجأت الى هذا المنتدى الذي التمست فيه خيرا علي أجد حلا .
عندي بوكس ufs كان يعمل عادي و لكن مع هذا التحديث الجديد اعطاني هاته الرسالة box_auth_error 9990 فهل عندكم من حل و لكم جزيل الشكر مسبقا. لاني مللت من هذا البوكس.
رد: ساعدوني لتحديث البوكس.
لقد اعتمدت هذه الطريقة و البوكس يعمل 100/100 .
Correction of errors -
BOX_AUTH_ERROR: HWK tampered or Substitute! in DCTxBB5 TOOLS v 2.2.0.1 and above****
and BOX_AUTH_ERROR: 9990 in UFS_SAMS 2.2.0.1 and above.
After a recent software update for UFS / HWK box having problems with authorization. Updating the firmware of the UFS**** with. Fbi file**** did not bring any results. Yes**** and there can be no results**** because the problem in the module itself HWK**** more precisely in its firmware. A flash can only be withdrawing from the UFS. information and wiring diagrams on the internet enough**** but I decided not to delve much into the process. information about the possibility of HWK firmware without removing it from the UFS and without connection to the service module contacts**** an invention or a competent look at things. For the firmware of the microcontroller unit (MSP430F1121A) requires the use of his pin TST**** which they brought only on service contacts (9 pin). You can see in Figure HWK module . So we have on board HWK normal**** but pretty cool**** the microcontroller ( MSP430F1121A ). Which is stitched through the BSL - Bootstrap Loader (you can read in the slau319a.pdf )
This flash microcontroller is very comfortable with the program MSPFET - FREE MSP430 flash programming utility ( author site ). You can download it from here ( version 6.1.1014 )**** or from the author. The program under Windows**** to test the under Win 7. program works with a serial (COM) port and emulates the BSL interface. In my case I used a USB-SERIAL Converter was built on the chip FT232RL**** or rather used his FT232RL Devel Module . So as you can use the original module UM232R from FTDI or any other USB-SERIAL converter**** for example**** PL2303**** wiring diagrams which can be found on the Internet.
For flashing use 6-pin microcontroller. Below is a table for ease of understanding -
Contact MC
Contact HWK
The signal port of a PC
Contact FT232R
2 (Vcc) - VCC 7 - 17 (3V3OUT) 4 (Vss) - GND 8 GND 7****18****21 (GND) 7 (RST / NMI) - RESET 6 DTR 2 (DTR) 14 (P1.1/TA0) - TXD A RX 5 (RXD) 10 (P2.2) - RXD 10 TX 1 (TXD) 1 (TEST) - TST 9 RTS 3 (RTS)
Using this converter on a chip from FTDI has pushed me to the presence of voltage 3.3V**** which generates the chip itself (FT232RL). That is**** there is no problem with its power supply IC firmware - Standard for MC 1.8 - 3.6v**** 4.1v max. Sam UFS HWK feeds voltage 3.0V**** fashionable and powered away. In addition to all on-board module HWK**** RESET of the microcontroller is pulled up to Vcc and TEST pulled up to the mass. That is**** Conclusions USB-SERIAL converter is directly connected to the service contacts HWK. To further simplify the connections I soldered HWK PIN HEADER (pin)
Then the jumper connected with his FT232 module for development**** which in this case plays the role of USB-COM converter.
For the firmware binary itself will need to be filled in by the microcontroller HWK MspFet.
Before working directly with the firmware**** USB-COM converter chip FT232R should be already connected and working**** that is**** drivers are installed and visible in Device Manager as a COM Port.(Some information about configuring the chip can be gleaned from an article on USBBit ). So as you need something to signals from the USB-COM nebyli inverted**** it can be viewed and corrected by the utility from FTDI - FTProg . ( Not a lot of information on the utility ).
ticks in the check-boxes should not be -
( Download the archive with the firmware )
1. Run MspFet (Further work has been described for version 6.1.1014)
2. Click the SETUP button and configure the program -
RST delay - 0 (Delays are not needed)
On the left side of the desired settings there**** except that the choice of the language program. On the right side**** select the adapter - BSL Port - port on your USB-COM (COM2 in my case) Path to V 1.60 -True (BSL versions V1.30 Lower than Support Only byte access operations. Therefore**** access to some of the memory cells will be limited**** as they WORD-orientation. ( slaa089a.pdf 7.3.1)) 38 400 Baud - False (use different Baud Rate from 9600 may affect the stability of the bond when flashing (slau319a.pdf 4/1)) port Keep Open - True (I do not know why) invert TST - False (do not invert the signal TEST) RST Invert - True (but RESET**** the normal port**** it is necessary to invert**** so the same signal can be inverted reset by checking the settings of the chip with FTProg**** as described above. But there is no need**** it's easier ismenit settings in the program that do.)
Ok**** the settings are saved. settings have been saved**** the modules are connected**** you can flash. 1.Open the firmware file 2. Choose our microcontroller - MSP430F11x1A !!! 3. Click ERASE to clear the memory IC (Trying to make a READ or VERIFY useless**** because the firmware recovery record and there is only a way to remove it and pour a new one) 4. Next**** write firmware - PROGR If all goes well**** we can see information about the successful completion of the firmware -
If the program talks about synchronization error **** then the microcontroller in the HWK is unwilling or unable to communicate with the program. There may be many reasons. Poor or not the right mix of devices**** non-functional devices. So the same problem may be trite to invert the signals. For vysneniya can play around with the inverted TST / RSR in the program settings**** try different combinations of these two points. After the firmware module is inserted back into the HWK UFS**** removing all unnecessary. After making sure to update HWK with momoschyu last HWK Update Client . I after This all worked fine -
Interestingly**** all resellers offer dumb flash itself UFS svom are generated FBI file on you**** or clog the bolt. PS: My "modernized" touched by new quartz pins on the board**** had to use duct tape -
المفضلات