Welcome to Medusa Box Software version 2.1.8
To make Repair Samsung GT-I9070 You need:
1. Connect it via Jtag cable to Box.
2. Connect to PC via USB cable (use both connection).
3. Install U8500 driver (if driver was not installed automatically) from folder "C:\Program Files\GSMServer\Medusa\Driver\U8500\" and try to connect the phone again.
Note: This phone can connect more longer, so You need to wait 30-50 seconds.
Connecting to server... Failed (Error: Could Not Connect)
Selected device model: Samsung GT-I9070
Connecting. Please wait...
Resetting target. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 62286041, IR Length = 6.
JTAG speed : 12000 KHz.
VREF level : 1.81 V
CPU : ST-Ericsson U8500
Core ID : 4BA00477
Storage Device: Sandisk eMMC SEM08G
Device ID : 00450001
Block size : 512 bytes
Blocks : 15269888
Storage size : 7.3 Gb
Connect successful.
Disconnected
Selected device model: Samsung GT-I9070
Connecting. Please wait...
Resetting target. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 62286041, IR Length = 6.
JTAG speed : 12000 KHz.
VREF level : 1.80 V
CPU : ST-Ericsson U8500
Core ID : 4BA00477
Storage Device: Sandisk eMMC SEM08G
Device ID : 00450001
Block size : 512 bytes
Blocks : 15269888
Storage size : 7.3 Gb
Opening "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Repair.mf" file...
Writing BOOT section. Please wait...
ERROR[025]: Read error or unexpected end of input file.
Resetting target. Please wait...
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 62286041, IR Length = 6.
JTAG speed : 12000 KHz.
VREF level : 1.81 V
CPU : ST-Ericsson U8500
Core ID : 4BA00477
Storage Device: Sandisk eMMC SEM08G
Device ID : 00450001
Block size : 512 bytes
Blocks : 15269888
Storage size : 7.3 Gb
Opening "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Repair.mf" file...
Writing BOOT section. Please wait...
ERROR[018]: Logical block operation failed at 176 Kb (Hex address 0x0002C000). Reason: Connection lost.
Connecting to server
Retrieving files list
Downloading file "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Repair.mf"...
Selected device model: Samsung GT-I9070
Connecting. Please wait...
Resetting target. Please wait...
VREF = 0.0V is less than required level. Please check target device power supply.
Medusa JTAG Firmware version 1.1.0.
Medusa JTAG Hardware S64 revision C.
Detected TAP ID: 62286041, IR Length = 6.
JTAG speed : 12000 KHz.
VREF level : 1.81 V
CPU : ST-Ericsson U8500
Core ID : 4BA00477
Storage Device: Sandisk eMMC SEM08G
Device ID : 00450001
Block size : 512 bytes
Blocks : 15269888
Storage size : 7.3 Gb
Opening "C:\Program Files\GsmServer\Medusa\Firmware\SAMSUNG_GTI9070_Repair.mf" file...
Writing BOOT section. Please wait... Done
Disconnected
Repair done.
المفضلات