وهذا الانفو بعد الRepair SL
Repair SL procedure started...
Phone Imei: 358634012926501
Key file exists, no need to read...
Operating mode is OK, no need change...
Writing SimLock Data... Ok
Writing SimLock Key... Ok
Done!
Read and Check phone data...
SDD Key status : SDData is Ok
CMLA Key status : read data error
SimLock status : SimLock Damaged!!!!!
- > Do REPAIR SL if it SL2/SL phone, if SL3 - Help Only Backup Or RPL

Security status : Security Damaged!!!!!
- > Do Local SX4 or Server SX4 , Upload Tune ( checkbox or manual )
-----------------------
PA_SimLock Version :
PA_SL phone detected
Setting FlashMode
FlashMode set Ok
1st boot Ok, C0
APE part info :
APE ASICID : 17100708
APE MODE ID : 00
APE PUB ID : D33FAF88FDD6339B0E8700545E46DEB9D2FB6189
APE R_HASH : 49A97E826B93BA20B7ED0B082475C005
APE ROM ID : 1DFD66132C872FD4
CMT part info :
CMT ASICID : 000000010000022600010006010C192101003000
CMT EM0 ID : 00000295
CMT EM1 ID : 00000B22
CMT PUB ID : 04F0001330EB0154C1277B80B2BD99433C3578A5
CMT MODE ID : 00
CMT R_HASH : BAF3A9C3DBFA8454937DB77F2B8852B1
CMT ROM ID : 273F6D55DFAAF68F
CMT : Sending 2nd loader...
Use : RAP3Gv3_2nd.fg , Rev : 0.0 Ver : 10.42.0
CMT Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 03
FLASHID : 22E800EC , CMT , NOR
CMT Flash ID : 22E800EC < SAMSUNG [SEC] => K5G2829ATC
FLCNT : 00000000000000000000000000000000000000
FLASHID : 0000FFFF , CMT , MMC , EXT
CMT Flash ID : 0000FFFF < Bad Flash Type , if MMC - It Ok
Sending ALGO....
Use : RAP3Gv3_algo.fg , Rev : 0.0 Ver : 10.40.0
CMT Algo sent
CMT PAPUB : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBD
Transmission mode : Dual (Ddr, TX2)
APE : Sending 2nd loader...
Use : helen3_2nd.fg , Rev : 0.0 Ver : 1.35.0
APE Loader sent, Boot Ok
MCU Configuration
MCU Cfg Ok , 02
FLASHID : 00A100EC , APE ,
APE Flash ID : 00A100EC < SAMSUNG [SEC] => K5E1G12ACM [NAND]
FLCNT : 010100FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF
Sending ALGO....
Use : h3_sam_nand_xsr.fg , Rev : 0.0 Ver : 1.47.0
APE Algo sent
APE PAPUB : 5E8D0D504A0902E261268C14FCD8A2C9093523BCBC
Transmission mode : Dual (Ddr, TX2)
Boot Done!
PrReq : NOR , 00
PrReq : NAND , 01030000504A0900E261260014FCD8
Init Service mode... Wait...
Connect phone on selected interface...

Connect phone on selected interface...
Phone found!
Series 60 Device detected!
read info... - Ok