.gif)
تم بفضل الله تفليش نوكيا 200 اشا علي الماكس كي بنجاح
السلام عليكم ورحمه الله وبركاته
تم بفضل الله تفليش فئه اشا الجديد نوكيا 200 الجديد بنجاح بفرجن 11.56
وده لوج التفليش
MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 3], SN: C08416A2
Using device: USB ROM and HTI, FW ver: 00.50, SN: 000107F4
Connection status: UHCI:HUB::USB 1.10 (Full-speed)
Driver: NMWCD, ver: 7.1.32.75
Module ver: 1.0.0.21151(13-07-2012), Library ver: 1.0.0.14195(13-07-2012)
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Make sure USB cable, Battery and charger are removed from device.
Insert USB cable, Battery back to device(make sure to have fully charged battery).
Insert Charger or Press phone's power button(if flashing doesnt start automatically)
Waiting for USB ROM device ...
Device synchronized.
CPU: XGOLD 213
Using embedded SBL from MCU.
Sending EBL Loader...OK
Sending EBL ...OK
Getting EBL Version ...
Boot mode: 0xCC
EBL version major/minor: 10.46
EBL version: Quantum_Bootloader_10.46_M1S1
Protocol version suggested by phone: 3
Set baud rate to: 6.50 Mbit/s
Flash ID: 0089 8982 - 23280001 [Intel NU48F512,512 Mbits]
CFI information:
Flash settings: 0/1024, size: 0x04000000
1 Block regions:
512 x 0x00020000 = 0x04000000
EBL ready !
Original IMEI: 35825904333958
RPL backup already exist (C:\mobileEx\3.5\data\backup\XGOLD_35825904333958_back.RPL)
Processing file: rm761__11.56.mcusw
Downloading item CODE:rm761__11.56.mcusw_ebl_psi.fls, num block: 4, size: 25.25 MB
Erasing area 0x40000000-0x4001FFFE ...OK
Programming completed in 0.406 s
Erasing area 0x40040000-0x4005FFFE ...OK
Programming completed in 0.406 s
Erasing area 0x40060000-0x4015FFFE ...OK
Programming completed in 1.672 s
Erasing area 0x40280000-0x41A7FFFE ...OK
Programming completed in 40.687 s
Checksum verified (0xC6C7)
Processing file: rm761__11.56.ppm_ma2
Downloading item CUST:package_ma2.ppm_ebl_psi.fls, num block: 1, size: 5.06 MB
Erasing area 0x41A80000-0x41F8F336 ...OK
Programming completed in 8.844 s
Checksum verified (0xF556)
Processing file: rm761__11.56.image_ma2_059J534_003
Downloading item CUST:package_ma2_059J534.image.fls, num block: 1, size: 14.50 MB
Erasing area 0x421C0000-0x43E1FFFE ...OK
Programming completed in 25.281 s
Checksum verified (0x9C85)
Total time for flashing process(boot+erase+write) was 8 min 54.375 s
Waiting for USB device removal ...OK
Waiting for USB device arrival ...
Waiting for device boot up ...
Device connected: nmwcdc\Nokia USB Phonet, PORT_ID: 10BDEC04
Verifying communication to device OK.
Phone type: RM-761 (Nokia 200)
SW version: V 11.56 26-03-12 RM-761 (c) Nokia
Imei plain: 35825904333958-9
Product code: 059J534
Language Pack:
- not available.
Imei net: 35825904333958
Version: SIMLOCK SERVER
Provider: GSM Test Operator
Counter: 0/3, 0/10
CONFIG_DATA: 0010100000000000
PROFILE_BITS: 800000000003000B
BLOCK1: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK2: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK3: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK4: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK5: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK6: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
BLOCK7: 1=OPEN, 2=OPEN, 3=OPEN, 4=OPEN, 5=OPEN
FULL FACTORY... OK
USER DATA... OK
LEAVE FACTORY... OK
SERVICE CENTER... OK
SOFTWARE UPGRADE... OK
PRODUCTION TUNING... OK
Reset User Code (to default:12345) ... OK
Completed in 0.281 s
ملحوظه -الفرجن الاخير11.64 عمل مشكله في التفليش بعد السوفت الجهاز لايدخل وضع اللوكل فالجهاز فصل معايا ففلشته بالفرجن ال قبله ال هو 11.56 اشتغل الجهاز بفضل الله تمام
رد مع اقتباس
المشاركة الأصلية كتبت بواسطة ahmad_zaky81
المفضلات