5130 كونتكت سيرفيس

[monshrf]

قراءة البوكس cyclone
Booting CMT...
CMT_SYSTEM_ASIC_ID: 000000010000022600010006030C192101033000
CMT_EM_ASIC_ID: 00000296
CMT_EM_ASIC_ID: 00000B22
CMT_PUBLIC_ID: 062002109A747F56A49D7E0A747B97F3FDC3BD24
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 9DDBFCFE6E73CED7D8C6268C8EB85723
CMT_BOOT_ROM_CRC: 273F6D55
CMT_SECURE_ROM_CRC: DFAAF68F
CMT Ready!
Searching for BootCode: DualLine 32Bit
RAP3Gv3_2nd.fg, Type: 2nd Boot Loader, Rev: 0.10.42.0, Algo: BB5
Flashbus Write baud set to 1.0Mbits
Flashbus Read baud set to 98Kbits
Using OLD BB5 FLASHING PROTOCOL
If software STUCK HERE with box TX LED lit, that means:
1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.
FlashChip[0,CMT]: 0x0089898200008A31, Intel, NOR
FlashContent[0,CMT]: 00000000000000000000000000000000, NOR
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
Transmission Mode Requested: Single Line, 8 bit, Accepted: Single Line, 8 bit
Searching for BootCode: DualLine 32Bit
FlashChip 0x00898982 (Intel), Size: 64MBytes, VPP: 9V
RAP3Gv3_algo.fg, Type: Algorithm, Rev: 0.10.40.0, Algo: BB5 ALGORITHM
Flashbus Write baud set to 2.0Mbits
Transmission Mode Requested: Dual Line, 32 bit, Accepted: Dual Line, 32 bit
Box TX2 Data Pin set to: Service Pin 3
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: 0C917F11196FDB7378C18EF7260698CA4489DCA0
APE Boot skipped on user request
Flashbus Write baud set to 5.0Mbits
Restarting MCU...
MCU Version V 06.65
MCU Date 01-04-09
Product RM-495 (Nokia 5130 XpressMusic)
Manufacturer (c) Nokia
IMEI 355246035523687
Mastercode 3573736462
IMEI Spare 3A55420653256308
IMEI SV 3355420653256338F2000000
PPM V 06.65, 01-04-09, RM-495, (c) Nokia , MEN
CNT Content: mena_a_red_ctv_mena_a_red, V 06.65, 01-04-09, RM-495, (c) Nokia , ,
PSN IIO772408
Module Code 0204024
Basic Product Code 0567772
PSD 0000000000000000
LPSN 0
RETU 16
TAHVO 22
AHNE 30
HW 2000
RFIC 06540601
DSP ICPR72_09w03
LCD SHARP
BT 2222-143C
Failed to read info -> Failed to read SP info
Selftests to proceed: 29
Passed ST_EAR_DATA_LOOP_TEST
Passed ST_SIM_CLK_LOOP_TEST
Passed ST_SIM_IO_CTRL_LOOP_TEST
Passed ST_SLEEP_X_LOOP_TEST
Passed ST_UEM_CBUS_IF_TEST
Passed ST_KEYBOARD_STUCK_TEST
Passed ST_CAMERA_IF_TEST
Passed ST_BACKUP_BATT_TEST
Passed ST_LCD_TEST
Passed ST_LPRF_IF_TEST
Passed ST_LPRF_AUDIO_LINES_TEST
Passed ST_CURRENT_CONS_TEST
Passed ST_RADIO_TEST
Passed ST_BACKLIGHT_TEST
Failed ST_SIM_LOCK_TEST
Passed ST_SECURITY_TEST
Passed ST_BT_WAKEUP_TEST
Passed ST_HOOKINT_TEST
Passed ST_TAHVOINT_TEST
Passed ST_BTEMP_TEST
Passed ST_IIC_TEST
Passed ST_EXT_DEVICE_TEST
Passed ST_CDSP_SLEEPCLK_FREQ_TEST
Passed ST_CDSP_SLEEPCLOCK_FREQ_TEST
Passed ST_CDSP_RF_BB_IF_TEST
Passed ST_CDSP_RF_SUPPLY_TEST
Passed ST_CDSP_TX_PLL_PHASE_LOCK_TEST
Passed ST_CDSP_RX_IQ_LOOP_BACK_TEST
Passed ST_CDSP_GSM_TX_POWER_TEST
Selftests done, Tests total: 29, Tests passed: 28, Tests not passed: 1

[NAPOLI]

الافضل ترفع اناليز سيكيورتي

وكما يبدو

Failed to read info -> Failed to read SP info

البوكس غير قادر على قراءة السيم لوك

فلش باعلى فرجن ثم ارفع اناليز للتاكد اكثر

من حالة السيم لوك

مع التاكد

1. You have not attached yellow TX2 Adapter (IT IS REQUIRED FOR BB5 PHONES WHEN USING JAF/UFS CABLES!)
2. Your cable is not TX2 Enabled!
3. Transmission error occured, try again
In either cases, you need to reconnect your box from USB.