بعض المعلومات عن الثحديث القادم FBUS2USB & TurboCache Flashed Phones

[ضياء الدين]

جديد


Hi, we will post small tests of new FBUS2USB and TurboCache funcionality.
This is probably best designed and working USB flasher currently on market.
Old ADL flashing is still possible,but...
Update is of course free for all Cyclone users, will be ready after current beta tests, and now few words about FBUS2USB:

- Supporting RAP3v3 phones
- Supporting RAPIDO phones
- Supporting RAPU phones
- Supporting RAP3GV4 Phones
- Supporting Broadcomm based phones
- Supporting APE phones (OMAP, ST based)
- Need just USB cable
- 100% FBUS 1:1 funcionality, FBUS packets is encapsulated into new protocol USB layer.
- Possible to Read Certificates (NPC,HWC,CCC)
- Possible to Write Certificates
- Possible to Erase Certificates
- Certificates managment is possible for APE block too
- Possible to SD Auth
- NOT possible to unlock
- Very fast and stable
- From technical point of view, no technical diffrence between FBUS and FBUS2USB flashing method - both use same loaders
- Will support current and upcoming Nokia phones
- Using exactly same GUI, and procedures as good old Cyclone FBUS flashing - less stres for customers




بعض التجارب


X2-00 Broadcomm based, Reading all Security Certificates

Booting CMT...
[BB5 NMWCD]: Found 0 active devices
[BB5 NMWCD]: Not Found!
1. Put phone battery out
2. Put phone battery in
3. Plug USB cable
4. Press power-on shortly
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.10.10.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.10.6.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E9700989029D9E899915F781B1582048E042A738
APE Subsystem Not Found
CMT NPC Ok
CMT HWC Ok
CMT CCC Ok
CMT R&D Ok
CMT VARIANT Not Found
CMT PAPUBKEYS Ok
CMT KEYS Ok
Restarting MCU...
Read all certificates finished

X2-00 full flash, total time 11.781 seconds

Processing pre flash tasks...
Pre flash tasks finished, continuing...
Processing rm618__04.80.mcusw (CMT)...
Booting CMT...
[BB5 NMWCD]: Found 0 active devices
[BB5 NMWCD]: Not Found!
1. Put phone battery out
2. Put phone battery in
3. Plug USB cable
4. Press power-on shortly
[BB5 BootRom]: Found 0 active devices
[BB5 BootRom]: Not Found!
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
rm618__04.80.mcusw, Type: Flash Image, Algo: BB5, XSR 1.6
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.10.10.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.10.6.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E9700989029D9E899915F781B1582048E042A738
Sending Certificates...
Certificates OK
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x00000000-0x0001FFFF, ONENAND
EraseArea[0,CMT]: 0x00020000-0x000203FF, ONENAND
EraseArea[0,CMT]: 0x00060000-0x011BFFFF, ONENAND
EraseArea[0,CMT]: 0x011C0000-0x01CFFFFF, ONENAND
EraseArea[0,CMT]: 0x02500000-0x028FFFFF, ONENAND
Erase Partition (CMT)
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 0.281s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Writing CMT KEYS Certificate...
Writing CMT PAPUBKEYS Certificate...
Writing CMT PRIMAPP Certificate...
Writing CMT PASUBTOC Certificate...
Writing CMT ADA Certificate...
Writing CMT RAP3NAND Certificate...
Writing CMT ISA+DYNSW Certificate...
Writing CMT MCUSW Certificate...
Writing CMT MCUSW1 Certificate...
Writing CMT GENIO_INIT Certificate...
Writing CMT UPDAPP Certificate...
Programming Status OK!
All blocks written OK! Time taken 6.656s
Flashing Speed: 33691,34 kBit/S
Restarting MCU...
Processing rm618__04.80.mcusw (APE)...
Processing rm618__04.80.ppm_b (CMT)...
Booting CMT...
[BB5 NMWCD]: Found 0 active devices
[BB5 NMWCD]: Not Found!
1. Put phone battery out
2. Put phone battery in
3. Plug USB cable
4. Press power-on shortly
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
rm618__04.80.ppm_b, Type: Flash Image, Algo: BB5, XSR 1.6
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.10.10.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.10.6.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E9700989029D9E899915F781B1582048E042A738
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x01D00000-0x024FFFFF, ONENAND
Waiting 320s for erasure finish...
Erase taken 0.47s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 1.234s
Flashing Speed: 40052,20 kBit/S
Restarting MCU...
Processing rm618__04.80.ppm_b (APE)...
Processing rm618__04.80.image_b_0595038_004 (CMT)...
Booting CMT...
[BB5 NMWCD]: Found 0 active devices
[BB5 NMWCD]: Not Found!
1. Put phone battery out
2. Put phone battery in
3. Plug USB cable
4. Press power-on shortly
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
rm618__04.80.image_b_0595038_004, Type: Flash Image, Algo: BB5, XSR 1.6
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.10.10.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.10.6.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E9700989029D9E899915F781B1582048E042A738
Partitioning...
Partitioning OK
Started group flash erase
EraseArea[0,CMT]: 0x02900000-0x0753FFFF, ONENAND
Erase Partition (CMT)
Waiting 320s for erasure finish...
Erase taken 1.0s
Writing all blocks...
Initializing TurboCache...
TurboCache Loaded!
Programming Status OK!
All blocks written OK! Time taken 3.891s
Flashing Speed: 37096,22 kBit/S
Restarting MCU...
Processing rm618__04.80.image_b_0595038_004 (APE)...
All images processed OK! Processing post flash tasks...
Post flash tasks finished!
Flashing successfully finished!

X2-00 IMEI Repair

1st Read Info, IMEI corrupted

[BB5 NMWCD]: Found 1 active devices
[Nokia X2-00 USB Generic]: Opening Connection
[Nokia X2-00 USB Generic]: Port opened OK!
MCU Version V 04.80
MCU Date 03-08-10
Product RM-618 (Nokia X2-00)
Manufacturer (c) Nokia
IMEI 12345610654321?
IMEI Spare 1A32541660452301
IMEI SV 1332541660452311F2000000
PPM V 04.80, 03-08-10, RM-618, (c) Nokia , B
CNT Content: b_0595038, V 04.80, 03-08-10, RM-618, (c) Nokia
PSN DNO288455
Product Code 0595299
Module Code 0204491
Basic Product Code 0591973
PSD 0000000000000000
LPSN 0
HW 1000
RFIC 9
LCD SEIKO
BT 2.31-SP2.31
Failed to read info -> Failed to read SP info

2nd Write NPC Certificate

Booting CMT...
[BB5 NMWCD]: Found 1 active devices
[Nokia X2-00 USB Generic]: Opening Connection
[Nokia X2-00 USB Generic]: Port opened OK!
Switching to RAW Mode...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
CMT_SYSTEM_ASIC_ID: 000000000000000022000509200C0000
CMT_EM_ASIC_ID: 00005361
CMT_PUBLIC_ID: 48400406073ECC4443B83B4151F972ABA08B3D66
CMT_ASIC_MODE_ID: 00
CMT_ROOT_KEY_HASH: 1B0D74C532CA1C6133940C740E8C786E
CMT_BOOT_ROM_CRC: DE56D582
CMT_SECURE_ROM_CRC: BDDE7A3A
CMT Ready!
Searching for BootCode: DualLine 32Bit
BCM21351_usb2nd.fg, Type: 2nd Boot Loader, Rev: 513.10.10.0, Algo: BB5
Using NEW BB5 FLASHING PROTOCOL
Transmission Mode Requested: Control USB, Accepted: Control USB
FlashChip[0,CMT]: 0x0000000000000000, Unknown, RAM
FlashChip[0,CMT]: 0xFFFF000000000000, Unknown, MMC
FlashChip[0,CMT]: 0x0020003000000131, ST, NOR
FlashChip[1,CMT]: 0x0000000100000000, Unknown, NOR
FlashChip[0,CMT]: 0x0020003000000131, ST, ONENAND
Searching for BootCode: DualLine 32Bit
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
FlashChip 0x00200030 (ST), Size: 128MBytes, VPP: Not Supported
BCM21351_XSR16_usbalg.fg, Type: Algorithm, Rev: 513.10.6.1, Algo: XSR 1.6
Initializing TurboCache...
TurboCache Loaded!
Writing CMT PASUBTOC Certificate...
Writing CMT ALG Certificate...
CMT Algorithm Ready!
Transmission Mode Requested: Bulk USB, Accepted: Bulk USB
Box TX2 Data Pin set to: Service Pin 3
Waiting for FUR Client become avaiable...
[BB5 BootRom]: Found 1 active devices
[Nokia USB Flashing Generic]: Opening Connection
[Nokia USB Flashing Generic]: Port opened OK!
FUR Avaiable!
Adding FUR Client (CMT, State: Ready)...
CMT FUR Ready!
Overriding VPP Setting, USB can't use VPP
Box VPP disabled
Internal CMT Phone VPP Enabled
PAPUBKEYS Hash for CMT: E9700989029D9E899915F781B1582048E042A738
APE Subsystem Not Found
Processing 48400406073ECC4443B83B4151F972ABA08B3D66_2010-11-28_180457.NPC.CMT.crt...
CMT NPC Erased
CMT NPC Written
Write CMT NPC Certificate finished
Restarting MCU...
All files processed OK!

3rd IMEI BACK

[

BB5 NMWCD]: Found 1 active devices
[Nokia X2-00 USB Generic]: Opening Connection
[Nokia X2-00 USB Generic]: Port opened OK!
MCU Version V 04.90
MCU Date 28-09-10
Product RM-618 (Nokia X2-00)
Manufacturer (c) Nokia
IMEI 352699049966024
Mastercode 554352325
IMEI Spare 3A25960994690602
IMEI SV 3325960994690622F0000000

[HaSHaM]

Thank you for the reporting

[NAPOLI]

الف شكر اخي الكريم

[mort83]

شكرا ضاوي حبيبي اخوك مرتضى الاسدي

[غدير فون]

مشكور صديقي ضياء على المتابعة الجيدة

[ضياء الدين]

شكرا ضاوي حبيبي اخوك مرتضى الاسدي

حبيبي مرتضى لاشكر على واجب

[moh_boulk18]

ماهو الجديد فى التحديث القادم

[ضياء الدين]

ماهو الجديد فى التحديث القادم

عزيزي هو الموضوع سهل التفليش بل USB للموديلات المذكورة

- Supporting RAP3v3 phones
- Supporting RAPIDO phones
- Supporting RAPU phones
- Supporting RAP3GV4 Phones
- Supporting Broadcomm based phones
- Supporting APE phones (OMAP, ST based)
-
سحب ال RPL وسترجاعه او مسحه وسرجاعه على شكل اجزاء
مثل NPC,HWC,CCC
اصلاح جميع المديلات المذكورة لمنطقة السوبر دنكل ولكثير من المزايا

[didivip1]

Thank you for the reporting

[z3x]

بارك الله فيك يا اخ