all hard resrt htc

[mafea55]

هذا الملف عبارة طريقة عمل فورمات لكل اجهزة htc

[al-najat]

ألف شكر على هذا الموضوع الخارق ونتما المزيد

[ROKA_aIR]

شكرا اخى الكريم لاكن لابد منك التوضيح عند عرض موضوع ليس ملف بة كلمات لم يفهمها بعض الاعضاء الغير محترفين ومنك المزيد

[mafea55]

اخ roka_air انا لما قمت بتنزيل الموضوع انا عارف قمت بتنزيل ايه والموضوع مفهم جدا كل جهاز
وتحتو الكبسات الي لازم نقوم بالضغط عليها واظن ان الموضوع مش محتاج للشرح
وشكرا لمرورك

I-MATE
Ultimate 6150
To perform a hard reset (also named a Cold Boot) by accessing the Master Clear Application:
Tap Start > Settings > System tab > Factory Setting - enter 1234. Confirm by tapping Yes.
The system will reboot to complete the operation. Alternatively, perform an hard reset
simultaneously holding the Power button and push the soft reset button inwards.
Release the buttons and the device will hard reset.
MITAC
Mio P350/P550
You can go back to the factory default executing an hard reset from Start-> Settings-> SysInfo-> Clean Boot
The display will show two methods:
Method 1: It will clean all data. Include Mio Map.
Method 2: It will clean all data, except Mio Map.
Mio a701
Make sure that A701 is turned off then press and hold at the same time the Down Volume button and the End button.
When the unit start to vibrate you can release both buttons. The unit will turn on automatically and it will show the
Setup Wizard. Follow the instructions to complete the operation
Mio a201
Remove the battery cover by pressing and then sliding the cover off.Use the stylus to slide the ON/OFF switch to
the ON (left) position . (ON to OFF , then OFF to ON) Install the battery and immediately press the Record Button.
The screen will show "cold boot" and "loading......" At this time, you must replace the battery cover.
Mio 168
Close all the running programs. On the rear of the unit slide the battery switch to OFF.
After about 1 minute return the switch on the ON position. The unit will restart with the original settings.
NEC
MobilePro P300
Hold the Power and Record buttons down and insert your stylus into the reset hole.
PALM
To perform a soft reset on a Palm (Handspring also) device find the reset button located in a hole on the back of
the device. Using the tool in your stylus, or some other object such as a paperclip press reset button inside the hole.
There is also another form of Reset: Warm Reset
A warm reset bypasses any system extensions (such as HackMaster hacks, operating system patches, and so on)
that are loaded on the device. A warm reset often bypass the "boot loop" error, allowing you to remove applications,
previously installed, causing problems. All stored data in the device remain unchanged with a warm reset.
To perform a warm reset hold down the top scroll button and press the reset button inside the hole on the back of
your unit. When in the Palm display you see the general preferences screen, release the top scroll button.
After a warm reset, you may need to perform a soft reset to get the device working as normal.
Performing a hard reset you start everything over from scratch. Be sure to back up your files first.
Perform a hard reset only if a soft or warm reset does not solve your problem.
To perform a hard reset hold down the power button (Wireless Mode button on the Treo 600) and press the reset
button on the back panel. When the Palm screen appears, release the power button.
You will get a message informing that you are about to erase all your data. To continue, press the top scroll button.
To cancel, press any other button. In this case you will get a soft reset only.
After a hard reset calibrate the digitizer and verify time & date.
QUANTA
xda Atom
Press and hold the power button, and then use the stylus to press the soft reset button at the same time.
TREO palmOne
Treo650
Remove battery cover and find the Reset hole beside the battery (without removing the battery). Press and Hold
down the Power/End button and using the stylus press and release the RESET button in the hole.
Release the Power/End button when the Palm Powered logo appears and when you will be asked if you wish to
remove all data press the Up button to confirm the Hard Reset.