أخيpikiche هل من حل في kp320تقف عند علامت kp320وماهو الكابل المستعمل
أخيpikiche هل من حل في kp320تقف عند علامت kp320وماهو الكابل المستعمل
1.........18
1: Gnd
2: Box Tx/Phone Rx (RJ45 pin-2)
3: Box Rx/Phone Tx (RJ45 pin-3)
5: Gnd
15: Gnd
18: Gnd
منقول للأمانة ولم اتعامل معهidentify with mcn box china :
Phone detected, wait..
CPU: 6229 Ver: 8A02 SW:8A02
CPU ID: 00200101
Initialize Boot...
Flash(Nand) Type: [TOSHIBA] TC58NVG0S3AFT
Flash(Nand) Code: 009800F1(00900095)
Flash(Nand) Size: 0x08400000 Hex Bytes
INT/EXT RAM Size: 0x00020000+0x00000000
Checking baud¡*
Set Baud:921600 OK.
Start Reading(Nand)...
Size: 0x8400000
اهلا بيك حبيبي كابل مستعمل هو KE500
ملاحضة هدا جهاز حبيبي في كتير من مشاكل منها hang on او logo on lcd screen واغلبية مشكل هدا يكون حله هارد يعني هاتف ادا توقف في فلاش يعني مشكلف هارد ولاتحبت عن حله الى عن طريق هاردوير
----------------
بوكس انفنتي حليت فيها مشكل جهازعنيد مند مدة وهدا لوج جهازي وكدالك سفتوير مستعمل في فلاش
سفتوير كالتالي : KP320-00-V10e-404-XX-APR-18-2008_A7610_07A_PCB03_GPRS_MT6229_S02[1].7S7610IN00-001-R2K_En_Hindi.B4Mكود PHP:
COM4 [VCP0] selected
module v2.72
Device: LG-KP320
Checking data, wait...
Action: write NAND flash
read mode: 01
write: Firmware
skip: Customization/Language Pack
skip: Customization
skip: Eeprom/ffs
source data: page only
identification#1 protocol ver: 04
ver. sw 1: A7610_07A_PCB03_GPRS_MT6229_S02.7S7610IN00-001-R2K.BIN
ver. sw 2: 7S7610IN00-001-R2K, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
end mark #4 found
nfi area detection finished: Ok
Boot ...
Press and HOLD Power button now !
19200 fixed
Connecting, wait...
Initializing [6229:8A02:8A02]...
CPU: MT6229
chip: 0031:2005:0101
status: FF
boot packet size: 0400
Release Power button now !
Boot Done
Initialize ...
version: 3.02
cpu-id: 09
loader: 3.748.0
NAND id: 98F19095
page size: 800+40
pages/block: 40
bits i/o: 08
address cycles: 04
blocks: 0400
external ram: 00000000
finalize connection...
done
emi configuration...
ram size: 00800000
emi configuration done
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
NOR: 0000:000000000000 [00000000]
NAND: 0098:00F100900095 [08400000]
NOR chip is not installed
Initialize Done
Set baud ...
921600
Set baud Done
Identification ...
ram test...
pass 1...
pass 2...
pass 3...
pass 4...
done
reading bootloader structure area (00080000 bytes)...
detecting bootloader structure...
warning: probably flash chip completely erased, no bootloader found
nfi area detection finished: failed
detecting bootloader structure by source file...
source data: page only
identification#1 protocol ver: 04
ver. sw 1: A7610_07A_PCB03_GPRS_MT6229_S02.7S7610IN00-001-R2K.BIN
ver. sw 2: 7S7610IN00-001-R2K, 00000000
ffs offset/size: 02000000/06000000
id-page1 Ok
nfi area detection finished: Ok
identification#1 structure: 2nd [standard] generation
identification#1 detection finished
Identification Done
Write ...
00006000 bytes sent
write core area 1 of 3...
00418800 bytes sent
write core area 2 of 3...
00AF9C00 bytes sent
write core area 3 of 3...
0037B400 bytes sent
Write Done
Finished, time used: 508 sec
Remove/Install battery now !
merci tankhs......................................... 1000000000000000000000
المفضلات