All Hard Reset for Pocket Pc

[winzou]

M700
Hold the Power button and press the Reset button using the stylus. Release both buttons at the same time and
next press the 'End Button' until the inquiry screen appears. Reply to the question.
x500+
If the touch screen is functional then tap Programs> Utilities and than Default Setting.
Otherwise Hold the “Power Button” and press the “Reset Button” with the stylus, and release both buttons
simultaneously. Next, hold the End Button until the system inquiry screen is displayed, then release the End Button
and answer the question(s) to perform a clean boot (Hard Reset).
x800
To perform a Clean Boot(Hard Reset) hold the “Power Button” and press once on the “Reset Button” with the
tip of the stylus, and release both buttons simultaneously. Next, continually hold the End Button until the
system inquiry screen is displayed, then release the End Button. Answer the question(s).

FUJITSU-SIEMENS /-
Loox 400 series
Simultaneously press reset button at the bottom using stylus cap and the Suspend/Resume button on top front
of the unit. After about 10 seconds a pictures will appear on th screen and a tone sounds
Loox 720 - 710
Use the point into the unscrewed stylus cap to press the soft reset button at the bottom and at the same time
press the button suspend/resume in front right corner. After about 10 seconds, when you will see a new screen
image and you will hear an advice sound, follows the relative instruction.
Loox n500/520
Take the stylus and screw it apart.
Press the tip into the soft reset opening and at the same time the suspend/resume and calendar buttons
Hold the suspend/resume and the calendar button pressed for a few seconds. The reset can take a few minutes.
A signal is sounded after the reset is complete. Follow the instructions
T830/T810
Slide off the battery cover and quickly remove an then refit main battery. Wait few seconds and athe same time
press the End button and the Reset button using the stylus tip. The screen will show some options.
Select SKIP to perform a normal cold start, or Factory Defaults if you confirm to performe an Hard Reset.
When a signal will sound follow the instructions on the screen

[winzou]

GARMIN /-
iQue 3000
press the reset button on the unit's back. Immediatly after press and hold the Power button until you see the
Palm Logo. Then release the Power button. You will see on the screen a message advising you are about to erase
all unit's data. Now you can press the upper half of the scroll button in front of the device to confirm the hard
reset or any other button to execute a simple reset instead.

GIGABYTE /-
g-Smart (i.Bond) Press the power button on the top and on the keypad press 7 and 9 (three buttons together)
It will display "formating" (Hardreset)

HANDSPRING
Hold down the power button on the front panel of your handheld. Holding down the power button, press the reset
button by paper clip. As soon as you see the logo on the screen, release the power button.
Press the up scroll button on the front panel to perform a hard reset or press any other button to perform a soft
reset. You can restore backed up data by performing a HotSync operation.

HP /-
Jornada 520, 525, 540, 545, 547, and 548
Press and hold the soft reset button and press the power button.
Jornada 564, 565, 567, and 568
Perform a soft reset using the button on the back of the device, thence remove the main and backup battery for
some minutes. (The backup battery is locked on the left side of the device)
iPaq 19xx Series
These devices can be hard reset by pressing and holding the soft recessed button on the left-hand side of the
device while you are pressing and holding the power button at the top the unit. Keep buttons pressed for several
seconds until the screen fades.
iPaq 22xx Series
Press and hold Buttons 1 (Calendar) and 4 (iTask) on the front of the device and, at the same time, press the Reset
button on the back of the Pocket PC using the device's stylus.
Hold thel buttons until the screen begins to fade (about 3/4 secs). Release the buttons and stylus. If the device
has been fully reset, it does not power on and you must reactivate its battery connecting the same to the AC power
or pressng the usual soft reset button with the stylus.

Note: The iPAQ 19xx & 22xx series have a feature called "iPAQ
File Store" allowing to store some data and programs in
the Flash ROM. If you used this option, the hard reset will
not cancel the data stored therein. Moreover if this area
become garbled you risk to have to reflash the Rom.
Do not store date exceeding its storage's space.

iPaq 41xx Series
Press and hold the Power button and at the same time press Reset button in the device's back using the stylus.
Release first the power button , thence the Reset button and you will see the device to reset and to power on
again with original setting.

[winzou]

iPaq rz17xx, rx31xx, rx34xx, rx37xx series
Press and hold the extreme left button (Mobile Media) and the extreme right button (iTasks) at the same time and
use the stylus to press the reset button at the bottom of the unit. When the screen fades release the two buttons
and button under the stylus. If the unit does not power on authomatically perform a simple soft reset.
iPaq hx4700
Press and hold calendar and iTask buttons in the front area, while, holding down the buttons, press using the stylus
the reset button on the bottom for about 2 seconds.
iPaq hx2750
press and hold button 1 and 4 on the front of the device and at the same time use the stylus to press reset button
on the bottom of the ipaq.
iPaq h6300
Press and hold the Power button for about 3 seconds while at the same time you press by the stylus the reset
button on the left side of the unit. When the screen blanks release both the buttons and wait that the device
powers on.
iPaq rx1950
To perform a clean reset and return you HP iPAQ to factory settings press and hold the calendar and the iPaq
Wireless buttons. While holding down the buttons lighttly press the Reset button by the stylus for about 2 seconds.
When the HP iPAQ screen begins to fade, release the two first buttons and then remove the stylus.
Plug the device into AC adapter o press Reset button again to restart unit.
hx2000 series (not h2210
Press and hold down Calendar and iTask buttons. While holding down these buttons, use the stylus to press the
Reset button on the bottom of the iPAQ for about two seconds. When the Pocket PC screen begins to fade, release
the mentioned two buttons first, and then remove also the stylus from the Reset.
hw6500 series
To perform an hard reset hold down the Power button and use the stylus to press the recessed Reset button on
the bottom for about five seconds. The screen fades and the device resets. Once the device resets and the screen
comes back on, release the Power button and remove the stylus from the Reset.
hw69xx series
To perform an Hard(clean) Reset press and hold the Answer/Send, Power, and End Call buttons. While holding these
buttons, by the stylus press the Reset button on the bottom of the iPAQ until the device restarts.
When the HP iPAQ restarts, release all of the buttons, Reset button included.
rw 68xx series
To perform an Hard(clean) reset and return your HP iPAQ to factory settings:
1. Press and hold the Answer/Send, Power, and End Call buttons.
2. While holding these buttons, use the stylus to lightly press the Reset button on the bottom of the HP iPAQ
until the device restarts.
3. When the HP iPAQ restarts, release all of the buttons, and then remove the stylus from the Reset button.
rx 57xx/59xx
To perform an Hard Reset(called factory reset) press and hold the Quick Launch and Rotate Screen buttons.
While holding these buttons, use the stylus to press the Reset button until the device restarts.
When the HP iPAQ restarts, release all of the buttons, and remove the stylus from the Reset button

[winzou]

HTC /-
qTek 2020-9090-S100 e Xda-Mda-O2-iMate etc
Press and hold the power button and use the stylus to press the soft reset button at the bottom of the unit at
the same time
HTC Wizard(qTek 9100 e i-Mate K-Jam, O2.. etc
Press and hold the Comm.Manager button along with Voice Command button.
While pressing the two button on the device, use the stylus to press and hold the reset button on the side.
HTC Prophet (Qtek S200,Imate JASmin etc
Press and hold the CAMERA and COMM MANAGER buttons, and use the stylus to press the RESET button.
Holds the CAMERA and COMM MANAGER buttons until the following message is displayed: “Press Send to restore
factory default or press other key to quit".
HTC TyTN(Hermes,Qtek9600,JasJam etc
Always switch off the device before to execute a full reset. The full reset is the Hard Reset of the device an to
execute it push and hold at same time both the SoftKey left and right on the front of the unit while you use the
stylus to press the soft reset button at the bottom of the device.
HTC Universal(qTek 9000 e i-Mate JasJar, Mda Pro..) etc
Press with the fingers the two keys the same time and keep them pressed. In addition by the stylus
press the pin into the RESET opening on the back of the device. Thence pressing 0 button confirm the Hard reset
or, using 'x', choice to not perform the Hard Reset.
(be careful to execute an hard reset under WM 5.0 read device's manual before)
HTC P3300 Artemis - HTC P3600 Trinity - HTC P3350 Love
Press and hold left and right button - SOFTKEY and using the stylus press the RESET command of the device.
Release the stylus, but hold the above buttons and release them when the screen shows the following message:
“Press SEND to restore manufacturer default, or press ..................”
Now you can press the required butto green call icon

[winzou]

HTC P3400 Gene
To perform a hard reset (Full Reset) press and hold the left SOFT KEY and the right SOFT KEY, and at the same
time, use the stylus to press the RESET button at the middle left side of your device.
Release the stylus, but continue pressing the two SOFT KEYs until you see the following message on the screen:
This operation will delete all your personal data, and reset
all settings to manufacturer default. Press Send to restore
manufacturer default, or press other keys to cancel.
Release now the two SOFT KEYs, and then press the TALK (Send) button
HTC P4350
Press and hold the left and right SOFT KEY, and at the same time, press the RESET button by the stylus.
Release the stylus, but continue pressing the two SOFT KEYs until you see the following message:
''This operation will delete all your personal data, and reset all settings to manufacturer default......''
Release the two SOFT KEYs, and then press the SEND button
HTC X7500/7501-(ATHENA/ADVANTAGE/Dopod U1000/T.Mobile AMEO
Slide the Volume slider down and at the same time, use the stylus to press the RESET button at the back of your
device. After a brief period of time, two choices will appear on-screen. Press the CENTER OK button to perform the
hard reset. (Otherwise, if any, press the CAMERA button to exit.)
HTC S620 Excalibur (T.Mobile Dash, Dopod C720W) - HTC S710 Vox
click Start > Expert > Cancel memory to performe an Hard Reset and follow the instructions shown on the screen.
The smartphone will restart immediately after the reset.
HTC Startrek Qtek 8500 (iMate SmartFlip/Qtek 8500/Star100/Dopod S300/Cingular 3125)
To reset the smartphone click Start > Accessories > Clear Storage. Follow the on-screen instructions to hard reset
The phone will restart after the reset.
HTC Touch Elf
. Press and hold the TALK and END buttons, and at the same time, use the stylus to press the RESET button at the
bottom of your device. Release the stylus, but continue pressing the above buttons until you see the following
message on the screen:
"This operation will delete all your personal data, and reset all settings to manufacturer default.
Press Action to restore manufacturer default, or press other keys to cancel."
Release the TALK and END buttons, and then press ENTER on your device.
Clear Storage
Another way of clearing the device storage and reset all setings back to factory default settings is to use the
Clear Storage feature. You will lose all your data and files on the device storage when you use Clear Storage, so
make sure to do a backup first.
Tap Start > Settings > System tab > Clear Storage. Enter “1234” then tap Yes

[winzou]

I-MATE
Ultimate 6150
To perform a hard reset (also named a Cold Boot) by accessing the Master Clear Application:
Tap Start > Settings > System tab > Factory Setting - enter 1234. Confirm by tapping Yes.
The system will reboot to complete the operation. Alternatively, perform an hard reset
simultaneously holding the Power button and push the soft reset button inwards.
Release the buttons and the device will hard reset.

MITAC
Mio P350/P550
You can go back to the factory default executing an hard reset from Start-> Settings-> SysInfo-> Clean Boot
The display will show two methods:
Method 1: It will clean all data. Include Mio Map.
Method 2: It will clean all data, except Mio Map.
Mio a701
Make sure that A701 is turned off then press and hold at the same time the Down Volume button and the End button.
When the unit start to vibrate you can release both buttons. The unit will turn on automatically and it will show the
Setup Wizard. Follow the instructions to complete the operation
Mio a201
Remove the battery cover by pressing and then sliding the cover off.Use the stylus to slide the ON/OFF switch to
the ON (left) position . (ON to OFF , then OFF to ON) Install the battery and immediately press the Record Button.
The screen will show "cold boot" and "loading......" At this time, you must replace the battery cover.
Mio 168
Close all the running programs. On the rear of the unit slide the battery switch to OFF.
After about 1 minute return the switch on the ON position. The unit will restart with the original settings.

NEC
MobilePro P300
Hold the Power and Record buttons down and insert your stylus into the reset hole.

PALM
To perform a soft reset on a Palm (Handspring also) device find the reset button located in a hole on the back of
the device. Using the tool in your stylus, or some other object such as a paperclip press reset button inside the hole.
There is also another form of Reset: Warm Reset
A warm reset bypasses any system extensions (such as HackMaster hacks, operating system patches, and so on)
that are loaded on the device. A warm reset often bypass the "boot loop" error, allowing you to remove applications,
previously installed, causing problems. All stored data in the device remain unchanged with a warm reset.
To perform a warm reset hold down the top scroll button and press the reset button inside the hole on the back of
your unit. When in the Palm display you see the general preferences screen, release the top scroll button.
After a warm reset, you may need to perform a soft reset to get the device working as normal.
Performing a hard reset you start everything over from scratch. Be sure to back up your files first.
Perform a hard reset only if a soft or warm reset does not solve your problem.
To perform a hard reset hold down the power button (Wireless Mode button on the Treo 600) and press the reset
button on the back panel. When the Palm screen appears, release the power button.
You will get a message informing that you are about to erase all your data. To continue, press the top scroll button.
To cancel, press any other button. In this case you will get a soft reset only.
After a hard reset calibrate the digitizer and verify time & date.

QUANTA
xda Atom
Press and hold the power button, and then use the stylus to press the soft reset button at the same time.

TREO palmOne
Treo650
Remove battery cover and find the Reset hole beside the battery (without removing the battery). Press and Hold
down the Power/End button and using the stylus press and release the RESET button in the hole.
Release the Power/End button when the Palm Powered logo appears and when you will be asked if you wish to
remove all data press the Up button to confirm the Hard Reset.

[winzou]

TOSHIBA
Toshiba E310

Slide the white switch on the bottom left to the left for a few seconds. The manual says depress the power button
at the top with the stylus in the hole in the back and release the power button.
Toshiba E740

Slide the white switch at the bottom of the device to the right for few seconds, thence slide it back.
Toshiba e800/805
Use the stylus to move to the right the switch under the rubber cover that you find above the wifi switch on the
bottom of device. After few seconds reinstate switch to original position.
Portege C500 (RG4-E01
Click Start > Settings > More > Perform Hard Reset then follow the on-screen instructions to reset the phone
that will restart after it has been reset.
Portege C900 (RG4-E02) Satellite
After you tried restarting your Toshiba phone, if it still deadlock or freeze, press the Reset button.
Even it still deadlock or freeze, remove the battery then re-insert the battery and turn your Toshiba phone on
and reinstate all settings.


UBIQUIO
501
To perform a hard reset press and hold the Comm Manager button and Voice Command button on the device.
Keep the two buttons pressed, and at the same time, use the stylus to lightly press and hold the RESET button

[simosoft83]

شكرا جزيلا