رد: 1209 كونتاكت
عملت كل حاجة والجهاز 1209 لا يقبل سوفت عملت اريز فلاش من على التوريندو وبعدين كل ما انزل فلاش على الجاف او mxkey الجهاز لايقبل سوفت من على كبل الايزى مع انه بيعمل تشك ياريت حد يساعدنى قراءة الجهاز من على الجاف هى
JAF version 1.98.62
Detected PKEY: 90038300
Card life counter: 100.00%
P-key nokia module version 01.02
Detected JAF INTERFACE version: 01.B1, Driver version: 40000, Library version: 30107
JAF DCT4/BB5 LOADERS DIR: C:\Program Files\ODEON\JAF\Flash\
JAF DCT4/BB5 PRODUCT DIR: C:\Program Files\Nokia\Phoenix\Products\
JAF USB LOADERS DIR: C:\Program Files\ODEON\JAF\FlashUSB\
JAF DCT3/DCTL LOADERS DIR: C:\Program Files\ODEON\JAF\Flash3\
USB Cable Driver version: 7.1.36.0
Changing mode...Done!
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: NONE
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: NONE
CNT Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh1050_nai5.71ic
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
CNT: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh1050_nai5.71ic
Booting phone...
Phone didn't answer with TX line high after UEM reset!
Causes:
1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
2.UEM damaged -> replace UEM.
MCU ID: 0xCCCC
This MCU ID is not supported in chosen flash file...
Error booting phone...
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: NONE
PPM Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh105_05.71ic
CNT Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh1050_nai5.71ic
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Phone Type:
FILES SET FOR FLASHING:
MCU Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh105_05.710
PPM Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh105_05.71ic
CNT Flash file: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh1050_nai5.71ic
ADSP Flash file: NONE
APE Variant file: NONE
APE User Flash file: NONE
Languages in ppm: English,Arabic,French,Swahili
Backing up PM Field 208 as RPL...
Setting local mode...
Failed! Aborting!
Failed to backup imei...
MCU: E:\ÝáÇÔÇÊ ÌæÌæ\RH-105\rh105_05.710
Booting phone...
MCU ID: 0x2292
BOOT file: C:\Program Files\ODEON\JAF\Flash\u3_2nd.fia
Loader version: 04.46.01 -> Revision: 0007
Boot size is 0x09A8
Boot is ready...
FLASH ID0: 88280020 <=> ST -> Type not in database Addr0: 0x01000000 - 0x01FFFFFF, SectorSize0: 10
FLASH ID1: 00010000 <=> Flash -> not used Addr1: 0x02000000 - 0x02FFFFFF, SectorSize1: 0
First 16 bytes: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Flash ID is 0x28882000
Flash loader is C:\Program Files\ODEON\JAF\Flash\u3_st_i.fia
Loader version: 04.46.01 -> Revision: 0007
Loader size is 0x4B38; Loader chk: df
Loader is ready...
Error Auth!
المشاركة الأصلية كتبت بواسطة amirhagag
08-08-2010, 11:55 AM
المفضلات