عند تفليش condor c4plus يعطيني الدانقل هذه الرسالة فما هو الحل
السلام علسكم
من فضلكم اخواني عند تفليش هاتف condor c4
سفشل الدانقل من إكمال التفليش وهذا هو الانفو
كود PHP:Operation : Check / Read Info [ v1.54 ]
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 38 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004E35585A4D4201FABFCE3371C9
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x00 , OEM : 0000
[eMMC] : FLASH_INF : [NOT_IN_BASE] ,
[eMMC] : FLASH_CID : 00000000000000000000000000000000
[eMMC] : FLASH_BRT : 0x00000000 , 0x00000000 , 0x00000000
[eMMC] : FLASH_LEN : 0x0000000000000000
[eMMC] : FLASH_UCP : 0 MiB [eMMC BAD_CONN]
DEV RID : 0xAE7BF7BFEE60EEB5D68D84665C653582
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : DA_HANDSET_ROM_INFO_NOT_FOUND
SOC VERIFY : C1
Boot Ok!
Info read not done :( Erased phone or unsupported FlashIc?
You can change settings : Settings -> Other -> NAND init Mode
Done!
Elapsed: 00:00:19
Reconnect Power/Cable!
وهذا انفو الفلاش
فارجو الحل من الخبراءكود PHP:Card found : S/N : D62DC3AD , v0132
Chinese Miracle II [MTK module] v 1.54
Scatter Load Ok , BaseBand : MT6572 , Project : Condor_PGN-403_jb3 , Storage : EMMC
Files found : 13 , Set to Flash : 12
Ready to Flash!
Operation : Flash [ v1.54 ]
======= Flash
1. Power Off Phone , Remove battery , Insert back
2. Insert USB cable. In some cases require hold BootKey
Wait for phone...
Phone found! [ 38 ]
Sync...
Inital Boot Ok!
BB_CPU_PID : 6572
BB_CPU_NME : [MediaTek] MT6572_S00
BB_CPU_EXT : 0xCA01 , 0x8A00 , 0x0000
Processing BROM stage
Settings for BROM configured!
SecCfgVal : 0x00000000
BromVer : 0x0005
BLVersion : 0x00FE
PreLoader : NOT Active [ Erased ]
BootLdrSS : NORMAL with SPRELOADER
Processing DA stage
DA Select done, will use MTK_AllInOne_DA_v5.1624.16.07
Sending and initialize DA ...
Running DA ver.4.2 on BBID : 0x88
NAND Flash : NOT INSTALLED
eMMC Flash : 1501004E35585A4D4201FABFCE3371C9
Initialize Memory ...
DRAM configured from ScatFW!
DRAM initialize passed!
DRAM size : 0x20000000
DAgent sent , init HW now
eMMC FlashIC initialized
[eMMC] : FLASH_VEN : 0x00 , OEM : 0000
[eMMC] : FLASH_INF : [NOT_IN_BASE] ,
[eMMC] : FLASH_CID : 00000000000000000000000000000000
[eMMC] : FLASH_BRT : 0x00000000 , 0x00000000 , 0x00000000
[eMMC] : FLASH_LEN : 0x0000000000000000
[eMMC] : FLASH_UCP : 0 MiB [eMMC BAD_CONN]
DEV RID : 0xAE7BF7BFEE60EEB5D68D84665C653582
INT RAM : 0x00020000
EXT RAM : 0x20000000 [512 MiB]
BOOT TYPE : DA_HANDSET_ROM_INFO_NOT_FOUND
SOC VERIFY : C1
Boot Ok!
ScatCFG : BaseBand : MT6572 , Project : Condor_PGN-403_jb3 , Storage : EMMC
Setting : Flash Pre-Erase (Safe) : Enabled
Setting : AFF verify : Enabled
Setting : HW verify : Enabled
Switching to HSUSB
HSUSB Init Ok
BL : Check HW compatibility
BL : BBID supported by BootLoader!
BL : Check eMMC compatibility
BL : eMMC NOT supported by BootLoader!
[BL_ERROR] : STORAGE : Break Flashing! This Firmware will kill phone!
Operation Failed
Elapsed: 00:00:22
Reconnect Power/Cable!
رد مع اقتباس
المشاركة الأصلية كتبت بواسطة rabiegsm
المفضلات