الرجاء المساعدة لايفلش 5130
السلام عليكم
ممكن المساعدة في جهاز 5130 كان شغال مافي شي بس تنظيف الجهاز من الفيروسات
فلشت الجهاز بفلاشة rm-495 7.97
مافلش
ماهة الحل وشم=كرا
هذه الرسالة
Uploading ALGO File...SendAlgoCodeFile_DCT5 : No Error - 0 (0x00)
============================================
OLD Protocol Detected... Using Turbo Mode...
============================================
Pabub KEY Request
No PAPUBKeysHash Returned
Read Type : FIASCO_BB5_DO_NOT_READ_CERTIFICATE (01)
Sending STORE_CERTIFICATE_REQUEST_BB5 (CMT 00 only)
Certificate 1
Name : NPC
ASIC Index : CMT 0
Certificate 2
Name : VARIANT
ASIC Index : CMT 0
Certificate 3
Name : R&D
ASIC Index : CMT 0
Certificate 4
Name : CCC
ASIC Index : CMT 0
Certificate 5
Name : HWC
ASIC Index : CMT 0
STORE_CERTIFICATE_REQUEST_BB5 : 61 05 2B 0D 4E 50 43 00 00 00 00 00 00 00 00 00 00 2B 0D 56 41 52 49 41 4E 54 00 00 00 00 00 00 2B 0D 52 26 44 00 00 00 00 00 00 00 00 00 00 2B 0D 43 43 43 00 00 00 00 00 00 00 00 00 00 2B 0D 48 57 43 00 00 00 00 00 00 00 00 00 00 85
STORE_CERTIFICATE_REQUEST_BB5 : No Error - 0 (0x00)
VPP Enabled by Software
Using Internal VPP
StartErase_DCT5...
BlockLength : 0x36 (54)
ERASE Blocks : 0x01 (1)
0 ERASE_AREA_BB5 0x12
Block Length : 0x33 (51)
BB ASIC Index : 0x00 CMT
Device Type : 0x00 NOR
Device Index : 0x00
0 : 00000000-000006BF
1 : 000006C0-0001FFFF
2 : 00040000-000BFFFF
3 : 000C0000-0013FFFF
4 : 00140000-0137FFFF
5 : 01380000-0151FFFF
Erase_SendEraseBlock_BB5_NOR
Task in Progress... Please Wait...
STATUS_REQUEST_BB5...
1 Sub Block ID : 14 STATUS_NOR_OK_BB5
Block Length : 01
BB ASIC Index : 00
Successfully erased..
Time Taken to Erase : 00:00:14
TRANSMISSION_TYPE_REQUEST_BB5 : 59 01 20 01 04 D9
ReturnedType : 04 DDR & 2TX
TransmissionTypeRequest_DCT5 : No Error - 0 (0x00)
Flashing Speed: 5.00 Mhz
Processing : rm495__07.97.mcusw
Total blocks to write : 1178
================================================
FBUS Cable RX2 PIN Diagnostics
================================================
STATUS_REQUEST_BB5...
1 Sub Block ID : 16 PROGRAMMING_ERROR_BB5
Block Length : 0F
BB ASIC Index : 00
Error Type : 05
Error Spec : 08
Offending Address : 00000400
Expected Content : 00009D3D
Detected Content : 00009D00
Reconnect your Cable Properly because RX2 PIN
is NOT getting any DATA from the Box!!!
================================================
ERROR: RX2 PIN is NOT CONNECTED PROPERLY !!!
================================================
Flashing FAILED
BB5_WRITE_FlashFile_0
Go to Settings -->
Nokia Settings -->
FBUS DDR&2TX Synchronization Timeout
Change the current value selected to a higher value
and Restart AdvanceBox.exe software to apply it
Operations Failed....
رد مع اقتباس
المفضلات