قائمة الاعضاء المشار اليهم

النتائج 1 إلى 2 من 2

الموضوع: 2600c

  1. #1
    .: جيماوي محترف :.
    الصورة الرمزية البرنس عمرو

    الحالة
    غير متواجد
    تاريخ التسجيل
    Oct 2008
    الدولة
    المنصوريه جيزة
    Sonork
    100.1620922
    Phone
    متنوع
    المشاركات
    3,682
    الشَكر (المُعطى)
    28529
    الشَكر (المُستلَم)
    4192
    الإعجاب (المُعطى)
    135
    الإعجاب (المُستلَم)
    36
    غير معجبون (المُعطى)
    0
    غير معجبون (المُستلَم)
    0
    تم تذكيره فى
    0 مشاركة
    تمت الاشارة اليه فى
    237 مواضيع
    معدل تقييم المستوى
    150

    Lightbulb 2600c

    بسم الله الرحمن الرحيم

    ممكن حد يعرفان الرسل ده كل ماجى اعمل سوفت نوكيا

    Getting MCU ID
    Phone didn't answer with TX line high after UEM reset!
    Causes:
    1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
    2.UEM damaged -> replace UEM.

    MCU ID: 0xCCCC
    Failed! Aborting!
    Done!
    Phone Restarted...
    FILES SET FOR FLASHING:
    MCU Flash file: NONE
    PPM Flash file: NONE
    CNT Flash file: NONE
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-340\

    Searching for default ******** of ini...
    Checking path: \Products\RM-340\
    Searching for JAF saved ******** of ini...
    Checking path: C:\Program Files\Nokia\Phoenix\Products\RM-340\
    No ini files found...
    FILES SET FOR FLASHING:
    MCU Flash file: NONE
    PPM Flash file: NONE
    CNT Flash file: NONE
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Phone Type:
    FILES SET FOR FLASHING:
    MCU Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.mcusw
    PPM Flash file: NONE
    CNT Flash file: NONE
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Phone Type:
    FILES SET FOR FLASHING:
    MCU Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.mcusw
    PPM Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.ppm_ic
    CNT Flash file: NONE
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Phone Type:
    FILES SET FOR FLASHING:
    MCU Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.mcusw
    PPM Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.ppm_ic
    CNT Flash file: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.image_ic
    ADSP Flash file: NONE
    APE Variant file: NONE
    APE User Flash file: NONE
    Backing up PM Field 208 as RPL...
    Setting local mode...
    Failed! Aborting!
    Failed to backup imei...
    MCU: C:\********s and Settings\M.S.H\Desktop\rm340__07.60.mcusw
    Booting phone...
    Phone didn't answer with TX line high after UEM reset!
    Causes:
    1. BSI line is not connected properly in connector -> Check cable, also for 3.3k resistor in serial with bsi line.
    2.UEM damaged -> replace UEM.
    MCU ID: 0xCCCC
    This MCU ID is not supported in chosen flash file...
    Error booting phone...




  2. #2
    .: جيماوي محترف :.
    الصورة الرمزية foxaaa

    الحالة
    غير متواجد
    تاريخ التسجيل
    Jan 2010
    العمر
    36
    المشاركات
    5,139
    تم تذكيره فى
    0 مشاركة
    تمت الاشارة اليه فى
    33 مواضيع
    معدل تقييم المستوى
    118

    افتراضي رد: 2600c

    تأكد من الكابل ونظافة مجسات التلامس التى على البورده

    ورجاء ذكر ما سبب التفليش وحالة الجهاز عند استلامه لانه الواضح من رسالة التشييك ان الهاتف به مشكلة صيانه

الكلمات الدلالية لهذا الموضوع

المفضلات

المفضلات

ضوابط المشاركة

  • لا تستطيع إضافة مواضيع جديدة
  • لا تستطيع الرد على المواضيع
  • لا تستطيع إرفاق ملفات
  • لا تستطيع تعديل مشاركاتك
  •