How you will Know if MTK is Fault Using GPGDRAGON
I have X6 China Mobile MTK Chips Dead set
Read info Using Flash Type Boots Ver3.920
Logs
Quote:
Initializing...
DA_LIB_VER_3.2.1.3
It is sensing the pinout fast,please hold on the phone Power key
RXD=8 TXD=5
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6225, HardwareVer:8A05, SoftwareVer:8A00
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 002088C400000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Get Project ID from phone...
ProjectID Not Found.
Read Info Using Flash Type Boots Ver3.848
Logs
Quote:
Initializing...
DA_LIB_VER_3.2.1.3
It is sensing the pinout fast,please hold on the phone Power key
RXD=8 TXD=5
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6225, HardwareVer:8A05, SoftwareVer:8A00
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 002088C400000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Get Project ID from phone...
ProjectID Not Found.
Read Info Using Flash Type Boots Ver.3.1016
Logs
Quote:
Initializing...
DA_LIB_VER_3.2.1.3
It is sensing the pinout fast,please hold on the phone Power key
RXD=8 TXD=5
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6225, HardwareVer:8A05, SoftwareVer:8A00
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 002088C400000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Config EMI...
Failed to check H/W.
Get Project ID from phone...
ProjectID Not Found.
In Three Flash Type Boots i Tried. Cant Detect Project I.D
هنا الحل
Here's The Tricks
I read Firmware even if Project I.D did not Detect Using Flash Type Boots Ver3.920
Logs
Quote:
Initializing...
DA_LIB_VER_3.2.1.3
It is sensing the pinout fast,please hold on the phone Power key
RXD=8 TXD=5
Connecting...Please hold on the POWER key until the red gauge is going...
BB:6225, HardwareVer:8A05, SoftwareVer:8A00
Loading boot...
INT_SYSRAM_BOOT test completed.
Loading boot...
Boot2 test completed.
Nor Flash ID: 002088C400000000
Nand Flash ID: 0000000000000000
Read Hardware Information is done.
Get Project ID from phone...
ProjectID Not Found.
Changing baudrate to 921600...
Done.
Reading full Flash...
Saved file to:
D:\********s and Settings\Administrator\Desktop\x6
All Done.
As you can see GPGDRAGON Read Firmware Using Flash Type Boots Ver3.920 Even if Project I.D is not Detected
you can use other Flash Type Boots that can Read Firmware
in this case you can figure that Flash I.C is Good
Now Proceed to Hardware Reheat MTK
After reheating MTK
Read info using Flash Type Boots Ver3.920
FORMAT Using Flash Type Boots Ver3.920
Write IMEI Using Flash Type Boots Ver3.920
DONE
المفضلات