C2-00 hardware id is missing

[samy2002]

لو سمحتوا ممكن مساعدة .. جهاز نوكيا c2-00 عند التفليش وتوصيل كابل usb تظهر رسالة خطا فى الويندوز .. وهى hardware id is imissing وبعدفترة قليلة البوكس يعطى erasing faild مع العلم انى جربت بوكس ufs واعمل على ويندوز 7 .. هل من حلول

[HosaaM HasheM]

الحل بتاكد من تعريفات الجهاز

و شحن البطارية و توصيلات ال usb

لو البور قريب منك فلش علية او استعمل موجب كابل الدراجون

[samy2002]

المشكلة مازالت قائمة .. تم تغيير الكابل ( اكثر من كابل ) وتغيير بطارية وثلاث بوكسات ( best-Atf-hwk ) واكثر من جهاز كمبيوتر ويندوز 7 وويندوز xp والمشكلة ما زالت قائمة يا ريت لو فيه راى مفيد .. لان المبتدى هيفكر فى تغيير الكابل والبطاريه .... الخ

[seakrokram]

ارفع لوغ التفليش على التيربو او البيست

[samy2002]

-> If Windows say "Unrecognized device" / Operation not start
-> Or if Phone start charge - just reinsert battery
-> If flashing freeze - reinsert cable/battery and try again
--- Press phone's power button or insert usb cable! ---

Connection opened successfully

IF Boot Init : 0xF0
IF Resp Len : 0x0A
IF xCPUID : XGOLD 213 [XMM2130 QUANTUM]
IF Resp Data : 1FB300020303010100FF

Sending EBL Loader ...
EBL Loader Ok, 01
EBL Loader ready, AA
Sending EBL ...
EBL sent Ok
EBL : Quantum_Bootloader_10.44_M1S1
Speed accepted, use 6.500.000
FLASHID : 89008289
FLIC conf set, RST set
Boot done!

Check keys...
Check done. Image can be flashed

Settings : EDM [0x8] , Block Mode , Fast CRC , Verify

===Flashing [MCU]===
File : rm704__03.99.mcusw
Image : rm704__03.99.mcusw_ebl_psi.fls
Sec-pack found, sending ...
Sec-pack sent
Found 5 region(s)
Processing Region 1/5
Erase , Start : 0x40000000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:01
Write , Start : 0x40000000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 2/5
Erase , Start : 0x40040000 , Len : 0x00020000
Erasing, wait ...
Erase done, time : 00:00:01
Write , Start : 0x40040000 , Len : 0x00020000
Flashing , wait ...
Region flash done, time : 00:00:00
Processing Region 3/5
Erase , Start : 0x40060000 , Len : 0x00100000
Erasing, wait ...
Erase done, time : 00:00:06
Write , Start : 0x40060000 , Len : 0x00100000
Flashing , wait ...
Region flash done, time : 00:00:04
Processing Region 4/5
Erase , Start : 0x40280000 , Len : 0x01940000
Erasing, wait ...
Erase done, time : 00:02:16
Write , Start : 0x40280000 , Len : 0x018C0000
Flashing , wait ...
Region flash error
[ERR_IfCheckResp] Result : 1C001E0201001B00

Error...
-> Check cable, flashfile, try again from this file

Connect phone on selected interface...


Elapsed: 00:03:47
Connect phone on selected interface

دة على البيست طبعا ....

[samy2002]

ودة لوغ العملية على ATF


Processing Image File :
rm704__03.99.mcusw
Processing Image File :
rm704__03.99.ppm_m_a
Processing Image File :
rm704__03.99.image_m_a_dgray_059C7R7


AUTO SELECTED DEAD USB FLASHING...

If Phone Booting does not Start in 5 Seconds,
Then Perform Steps 1, 2, 3 and 4...

1. Remove USB and Battery...
2. Insert USB.
3. Insert Battery. (Some phones boot automatically)
4. Please Power on phone shortly...


Infineon USB Boot: F00A1FB300020303010100FF
Sending PBL...
PBL Successfully Sent...
Sending SBL...
SBL Successfully Sent...
Setting Transmission Speed Done...
Flash Chip Manufacturer: Intel Electronics Corp.
Flash Boot Successful...
Unique Data: F00B0088AE046000
Original Product Code: 059J394
Reading : CCC... OK!
Reading : HWC... OK!
Reading : NPC... OK!
RPL Backup was Successful...
Plain RPL saved to:
C:\AdvanceBox Turbo Flasher\Nokia\Backup\359030045820523\359030045820523_55130.rpl
Certificate Block Saved to:
C:\AdvanceBox Turbo Flasher\Nokia\Backup\359030045820523\359030045820523_CERTIFICATE_05550EAE.bin
PM Block Saved to:
C:\AdvanceBox Turbo Flasher\Nokia\Backup\359030045820523\359030045820523_PMM_PROT_1A604D87.bin

Security Code: 12345

Data Sections : 04
Current File : rm704__03.99.mcusw
Compile Name: rm704__03.99.mcusw_ebl_psi.fls
Image Type : Main Firmware
Data Size : 27266440 Bytes

Sending Certificate Block
FIRMWARE Certificate Block Sent Successfully...
Processing Section 01
FIRMWARE Erase Block: 0x40000000~0x4001FFFE
Start Erasing...
Erasing Please Wait...
Block Erase Done...
Preparing Data Blocks...
Data Size: 131072 bytes
Data Checksum: 2A3C
Uploading Data Blocks to phone...
Block Write Successful...
FIRMWARE Data Blocks uploaded to phone...
Processing Section 02
FIRMWARE Erase Block: 0x40040000~0x4005FFFE
Start Erasing...
Erasing Please Wait...
Block Erase Done...
Preparing Data Blocks...
Data Size: 131072 bytes
Data Checksum: 7A82
Uploading Data Blocks to phone...
Block Write Successful...
FIRMWARE Data Blocks uploaded to phone...
Processing Section 03
FIRMWARE Erase Block: 0x40060000~0x4015FFFE
Start Erasing...
Erasing Please Wait...
Block Erase Done...
Preparing Data Blocks...
Data Size: 1048576 bytes
Data Checksum: 2B96
Uploading Data Blocks to phone...
Block Write Successful...
FIRMWARE Data Blocks uploaded to phone...
Processing Section 04
FIRMWARE Erase Block: 0x40280000~0x41BBFFFE
Start Erasing...
Erasing Please Wait...
Block Erase Done...
Preparing Data Blocks...
Data Size: 25952256 bytes
Data Checksum: 1244
Uploading Data Blocks to phone...
ERROR: Write Flash Failed
رسالة الخطا بتظهر على التربو بعد طول انتظار .. اولا بشكرك على الاهتمام انا عايز اتاكد الموبايل فى هذة الحالة سوفت ولا صيانة .. مع العلم ان رسالة Hardware id is missing بتظهر عند وضع البطارية ..

[seakrokram]

المشكلة هاردوير

[samy2002]

تم الحل .. تم الاتصال باحد خبراء الموبايل واخبرنى بعمل سوفت وير او بعمل ابديت فيرمورعلى برنامج الفونكس .. الغريبة عند تثبيت البرنامح وتوصيل كابل اليوس بى لم تظهر الرسالة.. تم تشغيل الجهاز بكل سهولة الحمد لله .. عموما اشكرك اخى على الاهتمام .. شكر جزيلا ..