نوكيا 101 ميت

[hamada yousri]

عندى جهاز نوكيا 101 rm-769 ميت قاطع باور نائى ودا ال تشك بتاعو على الماكس كى

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: C0853C24
Using device: HTI, FW ver: 00.50, SN: 0000E662
Connection status: OHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0 
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Boot error: CC CC CC 00
- Repeat the procedure. Sometimes it is a matter of temporary communication problem or similar.
- Check that all used cable are solid without any visible damage and have good contact. If possible, try with other cables.
- On rare occasions phone might be damaged or dead. So, if possible, try with another phone.

حاولت أفلشو جابلى الرسالة دى علما بانى وجدت الكابل المستخدم بة 2 بن فقط هل الكابل بتاع الجهاز دا 2 بن فقط ولا الكابل بة عيب فى الصنع

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: C0853C24
Using device: HTI, FW ver: 00.50, SN: 0000E662
Connection status: OHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0 
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
ERROR: could not boot device.

[hamada yousri]

تم تغيير الكابل وتفليش الجهاز ودا لوج الفلاش على الماكس كى ولسة نفس المشكلة الجهاز ميت ولا يدخل وضع لوكال مود ولا يعمل ضبط مصنع بعد الفلاش

MXKEY [MxKey Team HTI Flasher Interface (WinUSB) 4], SN: C0853C24
Using device: HTI, FW ver: 00.50, SN: 0000E662
Connection status: OHCI:HUB:USB 2.00 (Full-speed)
Driver: WinUSB, ver: 3.5.1.0 
Module ver: 1.0.0.21200(18-07-2012), Library ver: 1.0.0.14214(25-10-2012)
Device synchronized.
CPU: XGOLD 110
 Using embedded SBL from MCU.
Sending EBL Loader ...OK
Sending EBL ...OK
Getting EBL Version ...
 Boot mode: 0xCC
 EBL version major/minor: 10.24
 EBL version: Default_RAM_Bootloader
Set baud rate to: 921.60 Kbit/s
Flash ID: 0020 8804 - 23280001 [ST 58LR128U,128 Mbits]
CFI information:
 Flash settings: 0/64, size: 0x01000000
 2 Block regions:
  127 x 0x00020000 = 0x00FE0000
  4 x 0x00008000 = 0x00020000
EBL ready !
Processing file: rm769_006.650
 Downloading item CODE:hw_f3_rm769_r06.650.fls, num block: 3, size: 5.58 MB
Erasing area 0x00000000-0x00005FFE ...OK
Programming completed in 0.593 s
Erasing area 0x00800000-0x00BEFFFE ...OK
Programming completed in 1 min 16.812 s
Erasing area 0x00C5D000-0x00DFB6FE ...OK
Programming completed in 31.875 s
Checksum mismatch: Phone calculated 0xC177, software calculated 0x5824
Processing file: rm769_006.65ic
 Downloading item CUST:hw_f3_rm769_006.65ic.fls, num block: 1, size: 4.81 MB
Erasing area 0x00100000-0x005CFBFE ...OK
Programming completed in 1 min 41.094 s
Checksum mismatch: Phone calculated 0xFF05, software calculated 0xBE4D
Processing file: rm7690_nai06.65ic
 Downloading item CUST:hw_f3_rm7690_nai06.65ic.fls, num block: 1, size: 715.95 KB
Erasing area 0x00E60000-0x00F122BE ...OK
Programming completed in 14.688 s
Checksum verified (0x4E41)
Total time for flashing process(boot+erase+write) was 5 min 48.844 s

[seakrokram]

ارفع رسالة السيلف تيست

[hamada yousri]

ارفع رسالة السيلف تيست

الهاتف لا يقبل سيلف تست بضغط عليها مش بتفتح اى حاجة